Einleitung
Diese Anleitung zeigt, wie die USB-C Platine im MacBook Air (M1) von Ende 2020 ausgetauscht werden kann.
Was du brauchst
-
In diesem Schritt verwendetes Werkzeug:Magnetic Project Mat$19.95
-
Wenn dein MacBook unter BigSur v11.1 oder einer späteren Version läuft, lässt sich AutoBoot möglicherweise nicht stilllegen. Arbeite zuerst normal weiter, trenne aber den Akku sofort ab, wenn du ins Innere des Gerätes hinein gekommen bist.
-
Entferne folgende P5 Schrauben:
-
Zwei 7,9 mm Schrauben
-
Zwei 7,3 mm Schrauben
-
Sechs 2,6 mm Schrauben
-
-
-
Zwänge deine Finger zwischen das Display und das Gehäuseunterteil und ziehe nach oben, so dass sich das Gehäuseunterteil vom Air ablöst.
-
Entferne das untere Gehäuse.
-
Setze es passend auf und drücke fest darauf, damit die beiden darunter versteckten Rasten einschnappen. Du solltest das hören und spüren können.
-
-
-
Heble den metallenen Sicherungsbügel am Akkustecker mit dem flachen Ende des Spudgers hoch und entriegelt den Akkustecker.
-
Ziehe den Sicherungsbügel senkrecht nach oben, damit der Akkustecker aus seinem Anschluss auf dem Logic Board herauskommt.
-
Drücke, falls nötig, zuerst die hintere Seite mit den Kabeln fest, dann die vordere Seite des Steckers.
If having difficulty in flipping the bar up, place the machine vertical and not that there is a small “locking nib” that the bar has to clear. You may have to give the bar honest persuasion to clear the nib.
The bar can lock backwards making it very hard to even see let alone move. Great care is needed to shift it. I had to use two thumbnails, one on each side, then once flipped forward it takes more push than I expected to clip it in place. Ensure the plug is fully seated first !
As others commented, it can be hard to click the battery connector back into place. First make sure the bar is not underneath the connector. Then, turning the computer so the connector pins are facing you (LCD hinge end closer to you) can also make it easier to position the connector on top and then click it into place.
Some replacement batteries have a retainer bar that differs from OEM batteries. I had to swap the retainer bar to properly secure it under the "locking nib" to ensure it didn't release on its own (before it could freely swing).
-
-
-
-
Entferne die beiden 1,4 mm Torx T4 Schrauben, mit denen die Abdeckung des USB-C-Steckers befestigt ist.
-
-
-
Heble den Stecker des USB-C-Kabels mit dem flachen Ende eines Spudgers nach oben und löse ihn aus seinem Anschluss auf dem Logic Board heraus.
-
-
-
Entferne die beiden 2,9 mm Torx T5 Schrauben, mit denen die USB-C Platine befestigt ist.
-
-
In diesem Schritt verwendetes Werkzeug:Tweezers$4.99
-
Entferne die USB-C Platine mit einer Pinzette.
An dieser Stelle habe ich aufgegeben. Das Bauteil läßt sich nicht herausheben, ohne die USB-Anschlüsse abzubrechen. Es ist nicht genug Platz vorhanden. Weiß jemand eine Lösung hierfür?
Entschuldigen Sie mein Deutsch, aber diese Anschlüsse sollten ohne Widerstand herausgleiten. Überprüfen Sie, ob dies die richtige Anleitung für Ihr Modell ist.
-
Vergleiche dein Ersatzteil mit dem Originalteil — möglicherweise musst du fehlende Bauteile übertragen oder Schutzfolien vom Neuteil abziehen, bevor du es einbauen kannst.
Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.
Es kann sein, dass das Laptop beim ersten Mal nach der Reparatur erst hochfährt, wenn es am Netzteil angeschlossen ist.
Entsorge deinen Elektromüll fachgerecht.
Hat die Reparatur doch nicht den richtigen Erfolg gebracht? Frage in unserem Forum nach Hilfe.
Vergleiche dein Ersatzteil mit dem Originalteil — möglicherweise musst du fehlende Bauteile übertragen oder Schutzfolien vom Neuteil abziehen, bevor du es einbauen kannst.
Um dein Gerät wieder zusammenbauen, folge den Schritten in umgekehrter Reihenfolge.
Es kann sein, dass das Laptop beim ersten Mal nach der Reparatur erst hochfährt, wenn es am Netzteil angeschlossen ist.
Entsorge deinen Elektromüll fachgerecht.
Hat die Reparatur doch nicht den richtigen Erfolg gebracht? Frage in unserem Forum nach Hilfe.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
34 weitere Personen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
21 Kommentare
This guide was excellent. Easy & painless, even though it was the most complex repair I've taken on myself. Thanks for saving time & money.
Do you sell the screws for the usb c board? I have lost one of the 1.4mm torx screws which hold down the connector of the usb board.
This was quite easy, thanks so much Carsten!
where can I get the part for my computer MacBook Air M1 2020 Usb-C connector model A2337 EMC 3598 serial CO2FN1R2Q6LC.
Where can I buy it online....
If you're in selected countries in Europe or the USA, you can now order this part from Apple directly using their Self Service Repair store :)
No need to get it from Apple Self service. Much easier from here:
https://techtoro.io/macbook-air/genuine-...
GENUINE INPUT/OUTPUT (USB-C) BOARD A2337
Product Code: 923-03553
Worked well. Took about 30 mins because I think the power connector didn't go on fully the first time. Had to plug it into a power adapter first before it would turn on by itself with the power button.
yes, that is always like that. After battery is disconnected, next laptop start must be with charging cable.
Both of us followed this guide and it seems not to have worked. I've done successful repairs in 2015 and earlier, but this 2020 computer is much harder to work with. The step that likely went wrong was plugging the new part into the logic board. It was also tricky to get the old part out and new part in.
Perfect thank you, I would say this guide made the process easy not moderate. Great saving fixing the port myself. Thank you again
Anyone have suggestions on how to get the USB-C module out (step 8)? It is a little hard to remove it given the angle and how tight everything is.
I just ordered my replacement from iFixit's Amazon store here for $15.99: https://www.amazon.com/dp/B085WC4212?psc...
If you pull the ribbon connector up a bit and just jimmy it while lifting up and out it'll come out.. but it is in there quite snugly. A nice easy replacement though! Found that I too had to plug in a USB-C power source to boot the first time after putting everything back together.
Awesome, I just replaced the USB C on M1 Air, took just 10 minutes. Thanks a lot.
success! awesome guide!
i recorded this fix and uploaded it to my YouTube channel. if anyone's interested: https://youtu.be/bUd97uoBMBk
I did the repair but noticed that the problem extends to the logic board the female port where you connect the usb card has a tiny burn on it. Is there any way to replace the female port that is on the logic board without having to replace the entire logic board? If so name or serial number of part and either a link to a tutorial/ or video of this repair would be massively appreciated. Thanks!
Nice an easy. Well done!
ESD safe mat, plugged into ground, with a wrist strap, also grounded, are the best best to protect the logic board.
Robin Ray - Antwort
Re-Assembly Tip: Before putting the screws back in, snap the lower case on and test to make sure the MacBook powers up. When I first re-assembled, I became very nervous I did something wrong because it would not power on. It turns out I just needed to plug the laptop into a power source for it to power up (despite having a good charge before disassembly). It was the perfect way to test the new USB-C ports!
Austin - Antwort
Big points to this one, especially for mentioning needing to plug the laptop in. The bottom case needs to be screwed in and laptop needs to be plugged in before it will boot.
Bayden Yazalina -
Wiha 4PL driver for these screws.
Greg Worrel - Antwort
Printing out all the images from this Ifixit guide prior to starting and using duct tape help me keep track of screws.
raju midjdeya - Antwort
This Guide has a high chance of not working if an aftermarket display is used as MAC serialization was introduced post ~2023. Likely you will need an original MAC screen replacement and to serialize the display for it to work.
Tron Computers - Antwort