Zum Hauptinhalt wechseln

Repariere deine Sachen

Recht auf Reparatur

Werkzeug & Ersatzteile


Hier wird der Austausch des Akkus gezeigt.

Hinweis: Wenn sich ein dünner Plastikfilm auf dem Ersatzakku befindet, versuche nicht ihn zu entfernen. Er ist darauf verleimt und schützt den Akku, wenn er im Inneren deines MacBooks eingebaut ist.

    • Bevor du anfängst, fahre dein Gerät herunter. Schließe das Display und lege es umgekehrt auf eine weiche Oberfläche.

    • Entferne die folgenden zehn Schrauben:

    • Zwei 9 mm Pentalobe P5 Schrauben

    • Acht 2,6 mm Pentalobe P5 Schrauben

    • Der Spezialschraubenzieher, der zum Entfernen der zehn 5-Punkt Pentalobe Schrauben benötigt wird, ist hier erhältlich.

    Pulling the fan cable out was terrifying but you actually just pull on the cable itself. No way to get any leverage at the connector to dislodge it. Did come out easily but like I said, scared me!

    allison - Antwort

    Draai de schroefjes voorzichtig los en leg ze op een stabiele plek neer en let erop dat de schroefje een verschillende lengte hebben.

    bwgvanderveer - Antwort

    I thought I could replace my 256 Gb SSD with 512? regards

    ola m - Antwort

    Do you have good Test Point Voltages? It appears there are silver colored Test points on the I/O Board. I am working on a water spill and trying to troubleshoot if both the I/O board and the Logic need replaced.

    andrew - Antwort

    It's probably not necessary but may be a little safer to completely discharge the old battery before replacing it.

    Larry Smith - Antwort

    tell a model that was not inferior to the speed of the one in the laptop.

    Thank you

    ilyabuhov - Antwort

    Do i need to order tools separately to replace the battery i just ordered?

    anne uhlir - Antwort

    im looking for a Logic Board for a

    Apple - MacBook Air® - 13.3" Display - Intel Core i5 - 8GB Memory - 128GB Flash Storage (Latest Model) - Silver Model: MQD32LL/A

    Any help is appreciated.

    Jamie Comstock - Antwort

    P5 pentalobe screwdrivers are too big! The correct size for these screws are p4 pentalobe. P5 pentalobe was just able, with difficulty, to turn some of the screws. If the screws were at all tight, my p5 was unable to get them out, and started to strip the screws. A p4 screwdriver fit better and removed the screws with ease. (I was using high quality Wiha brand screwdrivers.)

    William Skinner - Antwort

    I had same experience (with MacBook Air 13-inch Mid-2012) … had to get P4, which worked swimmingly

    eric -

    Very simple installation. The screwdriver heads were exactly what we’re needed, one head for the outside case screws, the other for the screws holding the battery in place. The computer started right up. Now to see how the battery holds up, but I have a good feeling about this!

    Dennis Eaton - Antwort

    My P5 and the T5 worked perfectly with my early 2015 Air 13”! And it is super fast! Thank you iFixit!

    Pennny Beach - Antwort

    The supplied kit and instructions worked perfectly!

    Nikolay Andreev - Antwort

    Comments that the P5 pentalobe are too large are absolutely spot-on. There is no way the P5 pentalobe bit I have will work with the MacBook Air without destroying the screws. Hard target search for P4 pentalobe bit in progress…..

    joemoog - Antwort

    Bonjour j’aimerais changer mon SSD de 128 Go pour en mettre un de 512 Go. Je ne sais pas ce qu’il faut prendre car il faut qu’il soit compatible avec le macbook air A1466. J’aurais vu un Samsung Evo 970 500 Go mais si je ne me trompe pas, il faut un adaptateur.

    Merci pour votre aide.

    chicco33 - Antwort

    oui, vous aurez besoin d’un adaptateur, pour completez le changement.

    Dan -

    The tool kit should include tweezers for re-inserting the battery connector.

    Andre Clement - Antwort

    P5 pentalobe worked perfectly for me. Instructions were spot-on. Antenna connections were a bit fiddly to refit but got them in ok.

    michaelquinnell - Antwort

    Maybe the problem some are experiencing is that the designations are confusing (blame Apple rather than iFixit). the P2 is also known as PL1. The P5 is also known as PL4. The P6 is also known as PL5. So it is possible to mistake the P6 (PL5) for the P5 (PL4), meaning it (P6-PL5) will be too big, while the P5 (PL4) will be just right. Sort of a 3 Bears explanation, but it is very confusing.

    Thomas Lewis - Antwort

    I have not replaced a display on the A1369 but have done many A1466 which is a newer 13” model. They seem really similar and its not clear why one needs to remove the logic board to remove the display. The antenna cables on the A1466 dont have to rest under the logic board but can be tucked in the hinge crevice. Cant this same thing be done with the A1369?

    Sean Love - Antwort

    Did mine today - but new battery wasnt charging. Went back in and noticed the battery connector cable was not quite 100% “seated. It was sticking out by less than a millimetre! - you need to give it quite a firm push in to get it seated properly. Otherwise - all ok .

    John Brennand - Antwort

    Just installed on a MacBookAir6,2 (13-inch, Early 2014).

    Was very easy.

    New iFixit battery looks great so far:

    Full Charge Capacity (mAh): 4922 -> 7333

    Jonathan Cross - Antwort

    Screw P5 Pentalobe 1.2

    Mario Verlent - Antwort

  1. Löse das hintere Gehäuse vom Air, indem du mit den Fingerspitzen zwischen Display und Gehäuse gehst und es nach oben ziehst.
    • Löse das hintere Gehäuse vom Air, indem du mit den Fingerspitzen zwischen Display und Gehäuse gehst und es nach oben ziehst.

    • Entferne das hintere Gehäuse und lege es beiseite.

    There is a nub on the inside of the case which is attached to the battery. When you try to pull it open, it appears to be attached to the plastic casing of the battery, which sometimes splits. I gently unhooked the nub from the battery before removing the case fully. This seems to happen if the battery has suffered some drop damage (plastic parts broken around screws and parts of plastic frame split). Just an FYI in case your lower case doesn't pull away easily.

    Jeannie Crowley - Antwort

    When closing this back up make sure that the antenna cable is tucked away neatly

    Gabriel - Antwort

    So this is a legit back cover for MacBook Air?

    ASHANTI SMITH - Antwort

  2. Essential Electronics Toolkit

    Kompakte Alleskönner.

    Shop Toolkits


    Shop Toolkits
  3. Fasse die durchsichtige Plastiklasche, die am Akkuanschluss angebracht ist, an und ziehe sie in Richtung des vorderen Rands des Air, um den Akku vom Logic Board zu trennen.
    • Fasse die durchsichtige Plastiklasche, die am Akkuanschluss angebracht ist, an und ziehe sie in Richtung des vorderen Rands des Air, um den Akku vom Logic Board zu trennen.

    • Ziehe dabei den Verbinder keinesfalls nach oben!

    @&?! - pulled plastic tab on new battery to line up with logic board pins look to be coming out of male connector? Argh?!

    James Bowkett - Antwort

    Can expect anyone from ifixit to get back to me?

    James Bowkett - Antwort

    Hi James,

    It may be that one of the pins did not lock in properly into the plastic housing. You can try pushing the corresponding wire into the connector housing to try to lock the pin in.

    If that does not help, please respond to my email. Thanks!

    Arthur Shi -

    When I pulled the plastic tab, it separated from the battery connector. However, I was able to remove the batter connector using a scalpel to separate the batter connector and disconnect the battery from the logic board without any damage.

    Annabell - Antwort

  4. Entferne folgende fünf Torx T5 Schrauben, die den Akku am Gehäuse befestigen:
    • Entferne folgende fünf Torx T5 Schrauben, die den Akku am Gehäuse befestigen:

    • Drei 6,3 mm Schrauben

    • Zwei 2,4 mm Schrauben

    When going in reverse, it's easier to do step 3 before 4.

    John Heffernan - Antwort

    Screw normal torx T-5

    Mario Verlent - Antwort

  5. Wenn du am Akku arbeitest, vermeide es die vier offenliegenden Lithium Polymerzellen anzufassen oder zu drücken.
    • Wenn du am Akku arbeitest, vermeide es die vier offenliegenden Lithium Polymerzellen anzufassen oder zu drücken.

    • Hebe den Akku an der Kante an, die dem Logic Board am nächsten ist, und entferne ihn aus dem Gehäuse.

    • Wenn du einen neuen Akku eingebaut hast, solltest du ihn nach dem Einbau kalibrieren :

    • Lade ihn auf 100% auf und lasse ihn dann noch mind. weitere 2 Stunden laden. Benutze ihn dann normal, um den Akku zu entladen. Wenn angezeigt wird, dass der Akku zu laden ist, speichere deine Arbeit und lasse deinen Laptop an, bis er sich von selbst ausschaltet. Warte dann mind. 5 Stunden bevor du deinen Akku ohne Unterbrechung auf 100% auflädst.

    • Wenn du ein ungewöhnliches Verhalten oder Probleme nach dem Akkuwechsel bemerkst, dann hilft vielleicht ein Zurücksetzen des SMC (System Management Controller) deines MacBooks.

    Two Questions and a Comment:

    1) “Allow the battery to drain overnight” - Should the computer shut down automatically (during the first drain, as well)? If not, what percentage should the battery reach before charging it to 100%?

    2) While the battery is draining, can I use the computer?

    When installing the new battery, I found it much easier to insert the battery connector before screwing in the battery.

    Paul Larkin - Antwort

    When reinserting the battery, plug in the battery connector before screwing the battery into place. Some wiggle room is required to reconnect the batter and tweezers will help with the plugging in.

    Andre Clement - Antwort


Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.

Entsorge deinen Elektromüll fachgerecht.

Die Reparatur verlief nicht wie geplant? Schaue in unser Forum, da kann dir geholfen werden.

95 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:


Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Jeff Suovanen

Mitglied seit: 06.08.2013

287.835 Reputation

256 Anleitungen geschrieben


iFixit Mitglied von iFixit


115 Mitglieder

11.097 Anleitungen geschrieben

Thanks for this guide! From ordering the parts to doing to work, it was a super easy and fast process! May have been nice to see some mention of the different sized screws in various locations, and how to calibrate the battery once done with the install. Either way, awesome tutorial!

Elias Halsell - Antwort

@ejhalsell Good point about calibration—that’s been added to the final step now. There are measurements for every single screw though, so I’m not sure what more you’re looking for there.

Jeff Suovanen -

Just wanted to say thank you for this guide. It was extremely helpful and I appreciate the time you took putting it up!

Amy Lima - Antwort

How best should I dispose of my old battery? Would be nice to include this information.


Benjamin Hoste - Antwort

It’s hiding in the conclusion ;) “Take your e-waste to an R2 or e-Stewards certified recycler.” Thanks for disposing responsibly!

Jeff Suovanen -

This is great, but, in calibration, what do you mean by “before using it, allow it to drain overnight”? How do I drain it without using it?

brendan kelso - Antwort

@bpkelso Calibrate it before you start using it the way you normally would use it. ;) Until it’s calibrated, the battery charge percentage can be very unreliable and you may not get a true “full” charge out of it.

Jeff Suovanen -

It’s as easy as 1,2,3…

Great Company @ Great Guide ! Thank you for making it so darn easy !!!

Gianmarco Marchetti - Antwort

I wanted to express many thanks to iFixit for the part and the repair guide. Bless you.

Zack Paniel - Antwort

Could not have been easier. Took like 5 minutes to do the hardware replacement, and then ran a few browser windows with Netflix videos and an external DVD to run down the battery, as described. Great product, great writeup.

Ken Getz - Antwort

Surprise to see a guide to replace the battery for this model. Has anybody seen a battery decreased since installing Catalina?

Jose Cruz - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzten 24 Stunden: 65

Letzten 7 Tage: 494

Letzten 30 Tage: 2,215

Insgesamt: 83,361