Skip to main content

Einleitung

Nutze diese Anleitung, um die SSD zu wechseln. Dieses MacBook Air benutzt proprietäre Stecker am Speichermedium und ist deshalb ohne Adapter nicht kompatibel zu gewöhnlichen M.2 Laufwerken.

Führe, wenn irgend möglich, vor der Reparatur ein Backup deiner SSD durch. Mache dich dann vertraut mit der Wiederherstellung über das Internet, oder erzeuge ein bootfähiges externes Laufwerk, so dass du macOS auf dein neues Laufwerk installieren und deine Daten auf die neue SSD übertragen kannst.

Wir empfehlen sehr die Installation von macOS 10.13 High Sierra (oder eine neuere Version), bevor du die originale SSD deines MacBook Air austauschst. Die meisten neueren SSD erfordern neuere Laufwerkstreiber, die es in macOS Versionen vor HighSierra noch nicht gibt.

    • Bevor du anfängst, fahre dein Gerät herunter. Schließe das Display und lege es umgekehrt auf eine weiche Oberfläche.

    • Entferne die folgenden zehn Schrauben:

    • Zwei 9 mm Pentalobe P5 Schrauben

    • Acht 2,6 mm Pentalobe P5 Schrauben

    • Der Spezialschraubenzieher, der zum Entfernen der zehn 5-Punkt Pentalobe Schrauben benötigt wird, ist hier erhältlich.

    Pulling the fan cable out was terrifying but you actually just pull on the cable itself. No way to get any leverage at the connector to dislodge it. Did come out easily but like I said, scared me!

    allison - Antwort

    Draai de schroefjes voorzichtig los en leg ze op een stabiele plek neer en let erop dat de schroefje een verschillende lengte hebben.

    bwgvanderveer - Antwort

    I thought I could replace my 256 Gb SSD with 512? regards

    ola m - Antwort

    Do you have good Test Point Voltages? It appears there are silver colored Test points on the I/O Board. I am working on a water spill and trying to troubleshoot if both the I/O board and the Logic need replaced.

    andrew - Antwort

    It's probably not necessary but may be a little safer to completely discharge the old battery before replacing it.

    Larry Smith - Antwort

    tell a model that was not inferior to the speed of the one in the laptop.

    Thank you

    ilyabuhov - Antwort

    Do i need to order tools separately to replace the battery i just ordered?

    anne uhlir - Antwort

    im looking for a Logic Board for a

    Apple - MacBook Air® - 13.3" Display - Intel Core i5 - 8GB Memory - 128GB Flash Storage (Latest Model) - Silver Model: MQD32LL/A

    Any help is appreciated.

    Jamie Comstock - Antwort

    P5 pentalobe screwdrivers are too big! The correct size for these screws are p4 pentalobe. P5 pentalobe was just able, with difficulty, to turn some of the screws. If the screws were at all tight, my p5 was unable to get them out, and started to strip the screws. A p4 screwdriver fit better and removed the screws with ease. (I was using high quality Wiha brand screwdrivers.)

    William Skinner - Antwort

    I had same experience (with MacBook Air 13-inch Mid-2012) … had to get P4, which worked swimmingly

    eric -

    Very simple installation. The screwdriver heads were exactly what we’re needed, one head for the outside case screws, the other for the screws holding the battery in place. The computer started right up. Now to see how the battery holds up, but I have a good feeling about this!

    Dennis Eaton - Antwort

    My P5 and the T5 worked perfectly with my early 2015 Air 13”! And it is super fast! Thank you iFixit!

    Pennny Beach - Antwort

    The supplied kit and instructions worked perfectly!

    Nikolay Andreev - Antwort

    Comments that the P5 pentalobe are too large are absolutely spot-on. There is no way the P5 pentalobe bit I have will work with the MacBook Air without destroying the screws. Hard target search for P4 pentalobe bit in progress…..

    joemoog - Antwort

    Bonjour j’aimerais changer mon SSD de 128 Go pour en mettre un de 512 Go. Je ne sais pas ce qu’il faut prendre car il faut qu’il soit compatible avec le macbook air A1466. J’aurais vu un Samsung Evo 970 500 Go mais si je ne me trompe pas, il faut un adaptateur.

    Merci pour votre aide.

    chicco33 - Antwort

    oui, vous aurez besoin d’un adaptateur, pour completez le changement.

    Dan -

    The tool kit should include tweezers for re-inserting the battery connector.

    Andre Clement - Antwort

    P5 pentalobe worked perfectly for me. Instructions were spot-on. Antenna connections were a bit fiddly to refit but got them in ok.

    michaelquinnell - Antwort

    Maybe the problem some are experiencing is that the designations are confusing (blame Apple rather than iFixit). the P2 is also known as PL1. The P5 is also known as PL4. The P6 is also known as PL5. So it is possible to mistake the P6 (PL5) for the P5 (PL4), meaning it (P6-PL5) will be too big, while the P5 (PL4) will be just right. Sort of a 3 Bears explanation, but it is very confusing.

    Thomas Lewis - Antwort

    I have not replaced a display on the A1369 but have done many A1466 which is a newer 13” model. They seem really similar and its not clear why one needs to remove the logic board to remove the display. The antenna cables on the A1466 dont have to rest under the logic board but can be tucked in the hinge crevice. Cant this same thing be done with the A1369?

    Sean Love - Antwort

  1. Löse das hintere Gehäuse vom Air, indem du mit den Fingerspitzen zwischen Display und Gehäuse gehst und es nach oben ziehst.
    • Löse das hintere Gehäuse vom Air, indem du mit den Fingerspitzen zwischen Display und Gehäuse gehst und es nach oben ziehst.

    • Entferne das hintere Gehäuse und lege es beiseite.

    There is a nub on the inside of the case which is attached to the battery. When you try to pull it open, it appears to be attached to the plastic casing of the battery, which sometimes splits. I gently unhooked the nub from the battery before removing the case fully. This seems to happen if the battery has suffered some drop damage (plastic parts broken around screws and parts of plastic frame split). Just an FYI in case your lower case doesn't pull away easily.

    Jeannie Crowley - Antwort

    When closing this back up make sure that the antenna cable is tucked away neatly

    Gabriel - Antwort

    So this is a legit back cover for MacBook Air?

    ASHANTI SMITH - Antwort

  2. Android Fix Kits

    Ein neues Display oder Akku sind nur ein Kit entfernt.

    Jetzt kaufen

    Android Fix Kits

    Ein neues Display oder Akku sind nur ein Kit entfernt.

    Jetzt kaufen
  3. Um sicherzustellen, dass kein Strom fließt und dass sich das MacBook nicht einschaltet, während du arbeitest, ist es empfehlenswert, dass du den Akku trennst. Ziehe die durchsichtige Kunststofflasche, die am Akkustecker angebracht ist, in Richtung der vorderen Kante des MacBooks, um den Akku von dem Logic Board zu trennen.
    • Um sicherzustellen, dass kein Strom fließt und dass sich das MacBook nicht einschaltet, während du arbeitest, ist es empfehlenswert, dass du den Akku trennst.

    • Ziehe die durchsichtige Kunststofflasche, die am Akkustecker angebracht ist, in Richtung der vorderen Kante des MacBooks, um den Akku von dem Logic Board zu trennen.

    • Ziehe den Stecker nicht nach oben, wenn du ihn trennst.

    after disconnect the battery, press and hold 5*10 seconds the powerbutton on your keyboard to unload the capacitors

    Marcel - Antwort

    how does a person put the battery connector back in?- that is the only thing i’m afraid of touching after putting new fan in.

    a smith - Antwort

  4. Entferne die einzelne 2,9 mm Torx T5 Schraube, mit der die SSD auf dem Logic Board befestigt wird.
    • Entferne die einzelne 2,9 mm Torx T5 Schraube, mit der die SSD auf dem Logic Board befestigt wird.

    I'm using a T5 Torx screwdriver to remove the SSD retaining screw but it's simply not working, the screwdriver seems slightly too big and I even tried plyers to grab the ends of the screw and turn it but that didn't budge. Are the screws super tight or something? I can't figure out what I'm doing wrong

    smokey9112filmz2 - Antwort

    I would also like to know that, i have the same problem tried using a standard T5 Torx and the Pentalobe P5 screwdriver, but the both dont work/fit

    facebookvincent -

    I opened mine with a T-6.

    airshack - Antwort

    I ended up using the T5 with a rubber band in between. I wish I would have done this earlier. I stripped a little bit of the screw. You live you learn.

    Senh Mo Chuang - Antwort

  5. Hebe die SSD vorsichtig an einem Ende ungefähr 1,3 cm hoch und ziehe sie senkrecht aus ihrem Anschluss auf dem Logic Board. Hebe sie nicht mehr als 1,3 cm hoch - sonst könnten die SSD oder der Anschluss auf dem Logic Board beschädigt werden.
    • Hebe die SSD vorsichtig an einem Ende ungefähr 1,3 cm hoch und ziehe sie senkrecht aus ihrem Anschluss auf dem Logic Board.

    • Hebe sie nicht mehr als 1,3 cm hoch - sonst könnten die SSD oder der Anschluss auf dem Logic Board beschädigt werden.

    • Achte beim Wiedereinbau darauf, dass die SSD gut sitzt, bevor du sie mit der Schraube befestigst.

    Am I able to upgrade my Macbook Air early 2015 from 128Mb SSD to the SSD Samsung 960 (EVO or Pro) 1TB or 2TB?

    If so, do a need special adapters?

    Ruben Dominguez - Antwort

    Is there an adaptor cable or external housing that allows me to transfer the information on my SSD to my other laptop that has a SATA drive?

    Redwood Man - Antwort

    There are several available at Other World Computing.

    NerdsLimited -

    OWC 480 GB ssd says, early 2015 MacBook Pro needs thermal pad. what kin of pad is needed before SSD can be replaced.

    rasi_tip - Antwort

    Can you recommend an adapter to use a regular m.2 ssd?

    zepa - Antwort

    I really don’t recommend using M.2 SSD’s!

    As someone who services Mac’s I tend to see the failures and I’l warn you I see a lot of these M.2 drives with adapter with problems. As one of the first diagnostic processes I pop in my custom Apple Samsung SSD to see if the system works with it. If it does I recommend the power to replace the SSD.

    Dan -

    If I’m ordering a 1TB ssd what exactly should I be asking for ?

    i looked up a replacement for my 2015 Air and the ssd they sent had the slot in the wrong place. Will I need an adapter?

    why did they suggest it would be compatible (it’s an m2)?

    Colin Gray - Antwort

    Seems cheap isn’t good

    Colin Gray - Antwort

Abschluss

Um dein Gerät wieder zusammenzubauen, folge diesen Schritten in umgekehrter Reihenfolge.

71 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:

100%

Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›

Jeff Suovanen

Mitglied seit: 06.08.2013

251.619 Reputation

213 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Community

107 Mitglieder

9.392 Anleitungen geschrieben

Fairly straight forward once you get the right screwdrivers. Took me less than 10 minutes.

Jesse Collis - Antwort

Very simple and straight forward replacement. First-party SSD replacement can be found on ebay (typically removed from parted-out MacBook Airs). Currently they're aren't any third-party parts available.

rickhendricks - Antwort

Don't forget to re-attach the battery cable before closing up the underside... not that I did or anything ;-/

phil - Antwort

The Relevant Parts list all has incorrect links. Bait & Switch??

Examples:

"$199.95 Macbook Air 11" and 13" (Mid 2013/Early 2014) SSD, 256 GB"

Actually supplies: 128GB USED

"$349.95 Macbook Air 11" and 13" (Mid 2013/Early 2014) SSD, 512 GB"

Actually supplies: 256GB USED

carnthehawks - Antwort

Whoops! Looks like we didn't update the details on those parts when we updated the part itself, sorry about that!

Sam Goldheart -

How do I clone the content of my current ssd hard drive that I want to upgrade? Basically I want my macbook air ready for use once I install the new ssd drive.

Adrian James Paul Cabrera - Antwort

First off, you would need an enclosure with cable that would let you connect the new/replacement ssd/flash to your existing Air using a USB port. Then use Clone Carbon Copy and copy the inner drive to the outside drive. 30 minute process, at most. Then follow this well-done guide.

Phil L -

Hi all.

What is the maximum SSD accepted (and recognized by OSX) for Macbook Air Early 2014 ?

I have 256 GB. Can I go above this ?

ebay_mihai - Antwort

you can install what ever you want and your wallet is available to ^^

i have now the 500GB Samsung EVO 970 M.2 NVMe with an adapter installed. more is possible.

M.2 NVMe is the cheapest way to upgrade your MacBook. If you have to much money, you can also buy an OWC SSD (up to 1000$ for 2TB; Samsung 2TB 500$)

Marcel -

I looked into this and was told that the new SSD drives did not play well with this model. Comment ?

Michael T Kennedy - Antwort

Samsung evo 960 and sintech adapter works perfect. 2014 mba plug and play and time machine backup restore.

yesyes yes yes yes - Antwort

Hi! I already own this Inland Profession M.2 drive and would love to be able to use it for this project. Is it compatible, and if so, how do I find the proper adapter?

andrew.arthur.adams - Antwort

Has anyone had luck upgrading the SSD? I upgraded to the OWC X2 and now after the computer goes into hibernation mode it restarts twice before I can use it. This usually occurs in the mornings…

Will - Antwort

Hey Will! That’s a fairly common post-SSD-upgrade problem, unfortunately :( Here’s a forum post with a couple troubleshooting options you can try! Really an SSD doesn’t need to “hibernate” like a spinning drive does, so if nothing else works for you, you can always just disable hibernation. Sorry about the trouble!

Taylor Dixon -

I bought a Macbook Air 2014 and it didn’t come with an ssd. I ordered an OWC Aura pro x2 ssd and installed it. The Mac had El Capitan installed previously (I saw it on the Ebay listing). The new ssd would not appear in the disk utility menu. In the end I have a Macbook Air that I can’t get an operating software on. Any ideas?

J Jones - Antwort

Bonjour, j’ai essayé d’installer un ssd samsung 970 evo plus 500 GB sur mon macbook air début 2014. J’ai tout essayé mais impossible de réinstaller macOS sur la machine, ça plante tout le temps. J’ai tenté de remettre Mojave via le réseau wifi puis j’ai créé une clé usb (8GB) bootable avec Mojave dessus. Je démarre la machine en cliquant alt puis choisi de restauré macOS Mojave en utilisant ma clé. Je choisi la destination, soit le nouvel ssd et ça démarre. Sauf que ça plante toujours. Je précise que mon ssd est formater en macOS étendu (journalisé). Avez-vous une solution car là je ne sais plus quoi faire de plus ?

Merci

chicco33 - Antwort

Add Comment

View Statistics:

Past 24 Hours: 60

Past 7 Days: 429

Past 30 Days: 1,622

All Time: 205,563