Einleitung

This guide takes some time to complete and will not void your OnePlus 5's warranty. It is recommended to store the screws and parts together with their corresponding step in the guide to lower the chance of lost parts. No special skills are required for this guide.

  1. Always make sure to turn off the phone before attempting to replace a part.
    • Always make sure to turn off the phone before attempting to replace a part.

    • Power off the phone by holding down the rectangular power button on right side and pressing the red button that says "Power off."

    Kommentar hinzufügen

  2. Remove the two 1mm Torx #2 screws at the bottom of the phone by rotating the screwdriver counter-clockwise.
    • Remove the two 1mm Torx #2 screws at the bottom of the phone by rotating the screwdriver counter-clockwise.

    These are NOT T-2 torx. They are T-1. Waited a week for the T2 to come in only to find out that this guide is incorrect……

    Mike Broom - Antwort

    • Locate the sim card on the right side of the phone.

    • Insert the SIM ejector screwdriver bit into the hole left of the sim card holder by applying pressure.

    • It is also okay to use the SIM card eject tool for this step.

    • Remove the sim card holder by pulling it out with your fingers.

    Kommentar hinzufügen

    • Insert the plastic iFixit opening tool between the the plastic rim of the screen and the metal edge of the phone.

    • Place a suction cup on the screen to gain more leverage when separating the screen from the back plate.

    • Moving right to left around the phone, carefully pry the screen away from the back plate by wiggling the iFixit opening tool and pulling the suction cup in the opposite direction.

    • When reassembling, apply pressure to the edges of the screen and back plate together until they pop back into place.

    Kommentar hinzufügen

    • Locate the metal connector cap on the upper half of the device directly above the battery.

    • Remove the 1mm Phillips #0 screw from the metal connector cap by rotating the screwdriver counter-clockwise.

    Kommentar hinzufügen

    • Carefully pop out the metal connector cap with the nylon spudger and remove it by pulling up.

    Kommentar hinzufügen

    • Locate the two connectors directly above the battery on the left side of the device.

    • Remove the battery connector cable located to the right of the charging port connector cable using a nylon spudger by prying underneath it and popping it up.

    • Remove the charging port connector cable to the left of the battery cable using a nylon spudger by prying underneath it and popping it up.

    Kommentar hinzufügen

    • Remove the six 1mm Phillips #0 screws by rotating the screwdriver counter-clockwise.

    Kommentar hinzufügen

    • Remove the loudspeaker by gently pushing the spudger underneath it and prying it out.

    Kommentar hinzufügen

    • Notice the cable that goes across the yellow battery from the top to the bottom. There is a connector for this cable at the bottom of the battery.

    • Remove this cable by pushing a spudger underneath the connector and popping it out.

    Kommentar hinzufügen

    • Notice the two clear adhesive flaps overlapping on the left and right side of the yellow battery.

    • Peel back these flaps by running the spudger between the the flaps and battery, seperating the adhesive.

    • When reassembling the device, the spudger is not needed. Fold the flaps over so that the sticky side touches the yellow battery and connect the adhesive.

    • Be careful not to push too hard with the nylon spudger as you may pierce the battery and release toxic chemicals.

    Kommentar hinzufügen

    • Remove the yellow battery by pulling up and to the left on the green pull-tab.

    • This will create a ripping sound. This is because of the adhesive on the back of the battery and is completely normal.

    Kommentar hinzufügen

    • Remove the seven 1mm Phillips #0 screws by rotating screwdriver counter clockwise.

    • Remove the earpiece speaker connector located on the top of the motherboard using a nylon spudger by prying underneath it.

    • Remove the LCD screen connector located on the bottom of the motherboard using a nylon spudger by prying underneath it.

    • Disconnect the antenna wire located on the right side of the motherboard using a nylon spudger by prying underneath it.

    • The antenna wire will be clipped onto the motherboard so make sure it is fully unclipped before removing the motherboard.

    Kommentar hinzufügen

    • Remove the motherboard by gently pushing the spudger underneath upper right hand corner of the motherboard and prying it out.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

8 weitere Nutzer haben diese Anleitung absolviert.

Jose Velazquez

Mitglied seit 24.01.2018

494 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team S19-G1, Livingston Winter 2018 Mitglied von Cal Poly, Team S19-G1, Livingston Winter 2018

CPSU-LIVINGSTON-W18S19G1

4 Mitglieder

7 Anleitungen geschrieben

Nice. But where do you get the replacement part from?

Christos Mantas - Antwort

Dear Christos, hope it is not too late, you can check Oneplus 5 screen replacement from Witrigs

Witrigs - Antwort

My Display was broken so i had to order an LCD Screen Assembly from Witrigs. The Quality of it is really good, 1:1 OEM.

The Guide for the Replacement from iFixit is great at all, but there are 2-3 things missing. You have to remove the little kable for the Earspeaker on the Top of the Case, the Antenna Cable and the cables under the Loudspeaker/Microphone unit and under the Battery.

Kevin Kugler - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 14

Letzte 7 Tage: 75

Letzte 30 Tage: 397

Insgesamt: 2,836