Einleitung
Verwende diese Anleitung, um die Rückkamera in deinem Huawei P10 Smartphone auszutauschen. Bringe beim Zusammenbau an den erforderlichen Stellen neuen Klebstoff an.
Was du brauchst
-
-
Schalte dein Smartphone aus.
-
Entferne die beiden Pentalobe P2 Schrauben and der Unterkante.
-
Entferne das SIM Kartenfach.
-
-
-
Führe ein Plastic Opening Tool im unteren Teil des Smartphones zwischen Display und Gehäuse ein.
-
Heble vorsichtig das Display mit seinen Komponenten aus dem Gehäuse.
-
Nachdem du den unteren Teil des Smartphones aufgehebelt hast, verwende das Plastic Opening Tool, um die Klemmen an beiden Seiten des Gehäuses zu öffnen.
Hi! I cannot find a way to insert the plastic opening tool. Any suggestions on how I can create a gap to start. Everything seems quit rigid.
Also, where will I find your reply.
vbr/lars.skoldebring@gmail.com
Hi Lars, you might want to use a suction handle to lift the display and create a small gap to insert the plastic tool. If you don’t have a suction handle you can “build” a handle with tape that you stick onto the display in a shape similar to this —> __∏__ (also you may want to edit your post and remove your email address ;) )
Hi,
I’m stuck at this step for about two hours… There’s nothing I can do to open the case. Tried all kinds of opening tools and a suction handle. There is no gap at all between the display and the body. How can anything be inserted into a gap that practically does not exist? Please help.
Sorry to hear that. You could try and lift the display by using a suction cup and pull to create a small gap for a tool to get in.
-
-
-
-
Hebe das Display an und klappe es leicht nach hinten um.
-
Verwende einen Spudger, um den Stecker des Kabels für den An-/Aus-Schalter so wie die Lautstärkeregelung zu lösen.
Thanks JaL, of course it is.
-
-
-
Entferne die Kreuzschlitzschraube #00.
-
Verwende eine Pinzette, um die Metallklammer zu entfernen.
-
Verwende einen Spudger, um das Akku-Flachbandkabels vom Motherboard zu lösen.
-
-
-
Entferne die Kreuzschlitzschraube #00.
-
Verwende eine Pinzette, um die Metallklammer zu entfernen.
-
-
-
Verwende eine Pinzette um vorsichtig das untere Ende des Klebestreifens zu lösen, welcher den Stecker des Rückkamerakabels festklebt.
-
Verwende die flache Seite eines Spudgers, um den Stecker des Kamerakabels vom Motherboard zu trennen.
-
Entferne vorsichtig die Rückkamera.
-
Verwende diese Anleitung in umgekehrter Reihenfolge um dein Gerät wieder zusammen zu bauen. Bringe beim Zusammenbau an den erforderlichen Stellen neuen Klebstoff an.
Verwende diese Anleitung in umgekehrter Reihenfolge um dein Gerät wieder zusammen zu bauen. Bringe beim Zusammenbau an den erforderlichen Stellen neuen Klebstoff an.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
16 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
8 Kommentare
HI, I need to understand why many of us owners of the Huawei P10 has problems with the camera that does not focus or each photo is always blurred and it takes a side kick to fix it temporarily, then I would also know if changing the camera solve the problem. Thank you.
where to get the best rear camera replacement?
I have replaced the camera in my phone however the replacement does not work. I have seen comments from other people who have had a similar issue such as https://forum.xda-developers.com/p10/hel...
Could this be a firmware related issue? Perhaps the camera firmware in the replacement part is now older than that expected by the firmware in the phone itself?
Does anyone know where to find information about this sort of thing? Whenever I search the Googles I am always taken to generic pages about flashing boot loaders and various versions of Android, not the actual firmware.
where I can buy this camera as long as it is original?
What is misssing in detail: how to open the back case from the display. It was very hard and I need another webpage to get additional infromation.
Had the same Problem with the P9. Found something in the coments that did the trick for me: Additional to using the suction cup like mentioned in the instructions i had to (carefully?) preheat the aluminum back with a fan - it will expand slightly more than the glass front or the inside and come off like a charm after.
Thanks! I couldn’t really get the display out of the back case so I got some instructions from a youtube video for that. Other than that, very clear instructions and photos. My phone has a working rear camera again!
Thanks for this.
I successfully managed to change the camera
Das Honor 9 hat an der Unterkante keine Schrauben.
Wie ist das Honor 9 zu öffnen?
Michael Tuschek - Antwort
Vielleicht beantwortet diese Anleitung deine Frage ;)
Tobias Isakeit -
Hi, my P10 does not have screws, just two tiny holes. Do I push in here to unfasten? Einar, Norway
Einar Ryvarden - Antwort
Hi Einar Ryvarden,
in case you bought a used or refurbished phone, someone might have forgotten to put them back in. Since you have holes at the bottom edge next to the charging port this is likely. You can try to start with step 2 and see if you can lift the phone assembly (don’t forget to remove the SIM tray first). As far as I know there is no version of the regular Huawei P10 with no screws. However you there are none in the P10 lite and in the P10 plus, maybe one of the opening procedures for those phones might help you.
Dominik Schnabelrauch -