Repariere deine Sachen Community Store

WowWee MiP Robot LED Light Replacement

Einleitung

The LED light on the MiP indicates what mode the robot is in. If this light is malfunctioning, using the MiP is difficult.

Was du brauchst

  1. WowWee MiP Robot LED Light Replacement, Battery: Schritt 1, Bild 1 von 2 WowWee MiP Robot LED Light Replacement, Battery: Schritt 1, Bild 2 von 2

    • Remove the three 12.0 mm Phillips # 2 screws from the battery cover.

    Bearbeiten

  2. WowWee MiP Robot LED Light Replacement: Schritt 2, Bild 1 von 2 WowWee MiP Robot LED Light Replacement: Schritt 2, Bild 2 von 2

    • Carefully pull the battery pack from the robot.

    • Remove the batteries from the battery pack.

    Bearbeiten

  3. WowWee MiP Robot LED Light Replacement, Wheel: Schritt 3, Bild 1 von 2 WowWee MiP Robot LED Light Replacement, Wheel: Schritt 3, Bild 2 von 2

    • Use a metal spudger to carefully pry off the hubcap without marring the plastic wheel or hubcap.

    • This plastic material is not replaceable. Any damage will be noticeable.

    Bearbeiten

  4. WowWee MiP Robot LED Light Replacement: Schritt 4, Bild 1 von 2 WowWee MiP Robot LED Light Replacement: Schritt 4, Bild 2 von 2

    • Remove the 12.0 mm Phillips #2 screw.

    • Hold the wheel in place, or it will rotate as you attempt to remove the screw.

    Bearbeiten

  5. WowWee MiP Robot LED Light Replacement: Schritt 5, Bild 1 von 1

    • Pull the wheel off of the square axle.

    • Do not use excessive force while removing the wheel. Pulling too hard on the wheel can damage the axle.

    Bearbeiten

  7. WowWee MiP Robot LED Light Replacement, WowWee MiP Robot Body Disassembly: Schritt 6, Bild 1 von 2 WowWee MiP Robot LED Light Replacement, WowWee MiP Robot Body Disassembly: Schritt 6, Bild 2 von 2

    • Remove the eight 9.3 mm Phillips #1 screws from the back of the robot.

    Bearbeiten

  8. WowWee MiP Robot LED Light Replacement: Schritt 7, Bild 1 von 3 WowWee MiP Robot LED Light Replacement: Schritt 7, Bild 2 von 3 WowWee MiP Robot LED Light Replacement: Schritt 7, Bild 3 von 3

    • Remove the arms from the body.

    • Carefully open the body compartment.

    • Open the compartment slowly. There are wires connecting the two body pieces together. If pulled too hard, the wires and/or the motherboard could be damaged.

    Bearbeiten

  9. WowWee MiP Robot LED Light Replacement: Schritt 8, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    Tweezers
    $4.99
    Kaufen

    • Using precision tweezers, disconnect the following three bundles of wires:

    • Connecting the battery pack to the motherboard.

    • Connecting the power switch to the motherboard.

    • Connecting the speaker to the motherboard.

    Bearbeiten

  10. WowWee MiP Robot LED Light Replacement, LED Light: Schritt 9, Bild 1 von 2 WowWee MiP Robot LED Light Replacement, LED Light: Schritt 9, Bild 2 von 2

    • Remove the four 7.5mm Phillips #1 screws.

    Bearbeiten

  11. WowWee MiP Robot LED Light Replacement: Schritt 10, Bild 1 von 2 WowWee MiP Robot LED Light Replacement: Schritt 10, Bild 2 von 2

    • Carefully pull the motor and motherboard assembly straight out from the base.

    • Be careful not to break the plastic rods that go through the motor assembly and are connect to the shell.

    Bearbeiten

  12. WowWee MiP Robot LED Light Replacement: Schritt 11, Bild 1 von 1
    In diesem Schritt verwendetes Werkzeug:
    Tweezers
    $4.99
    Kaufen

    • Use the precision tweezers to unplug the bundle of wires.

    Bearbeiten

  13. WowWee MiP Robot LED Light Replacement: Schritt 12, Bild 1 von 1

    • Slide the head back to separate it from the body.

    • The motherboard does not need to be separated from the head to replace the LED light.

    Bearbeiten

  14. WowWee MiP Robot LED Light Replacement: Schritt 13, Bild 1 von 1

    • Remove the 7.5mm Phillips #1 screw.

    • The LED light is soldered to the small circuit board.

    Bearbeiten
Abschluss

To reassemble your device, follow these instructions in reverse order.

Eine weitere Person hat diese Anleitung absolviert.

Autor:in

mit 4 anderen Mitwirkenden

Courtney

Mitglied seit: 02/04/16

236 Reputation

1 Anleitung geschrieben

Auszeichnungen: 9

+ 6 weitere Auszeichnungen

Team

USF Tampa, Team 3-4, Wollert Spring 2016 Mitglied von USF Tampa, Team 3-4, Wollert Spring 2016

USFT-WOLLERT-S16S3G4

4 Mitglieder

10 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 5

Insgesamt: 624