Dell Inspiron 14-7437 Thermal Cooling Fan Replacement

Zuletzt aktualisiert am August 8, 2019

10 - 15 Minuten

Mittel

Einleitung

The Thermal-Cooling Assembly is used to keep your laptop from overheating while running. If this breaks and is not replaced you run the risk of frying your motherboard.

Was du brauchst

Werkzeuge

Schritt 1 Base Cover

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Base Cover: Schritt 1, Bild 1 von 2

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Base Cover: Schritt 1, Bild 2 von 2

Power off your Dell Inspiron 14-7437 before disassembling.
Remove the eight 4.5 mm screws on the back panel of the device using the Phillips 1 Screwdriver.
The two 4.5 mm screws in the center under the rubber mount cannot be removed, but can be loosened.

Übersetzen

Schritt 2

Pry open the back cover using a spudger and slide it along the under the cover.

Übersetzen

Schritt 3 Battery

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Battery: Schritt 3, Bild 1 von 2

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Battery: Schritt 3, Bild 2 von 2

Remove the two 2.5 mm screws holding the battery in place using the J000 Phillips Head Screwdriver.

Übersetzen

Schritt 4

Disconnect the ribbon cables from the motherboard.

Übersetzen

Schritt 5

Lift up and remove the Lithium-Polymer Battery.

Übersetzen

Schritt 6 Speaker

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Speaker: Schritt 6, Bild 1 von 1

Disconnect wires from Motherboard by gently pulling up.

Übersetzen

Schritt 7

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement: Schritt 7, Bild 3 von 3

Remove the speakers from the case.

Übersetzen

Schritt 8 Coin Cell Battery

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Coin Cell Battery: Schritt 8, Bild 1 von 1

Lift the coin cell battery wire, and carefully remove from motherboard.
There are little hooks that the wire is hooked under.

Übersetzen

Schritt 9

Remove the Coin-Cell Battery from the case.
There is a small amount of adhesive on the bottom of the coin cell battery.

Übersetzen

Schritt 10 Cooling Fan

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Cooling Fan: Schritt 10, Bild 1 von 2

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Cooling Fan: Schritt 10, Bild 2 von 2

Remove the two 2.5 mm screws using a J000 Phillips Head Screwdriver.

Übersetzen

Schritt 11

Pull up on the wire and remove the Cooling Fan.

Übersetzen

Schritt 12 Thermal-Cooling Assembly

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Thermal-Cooling Assembly: Schritt 12, Bild 1 von 3

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Thermal-Cooling Assembly: Schritt 12, Bild 2 von 3

Dell Inspiron 14-7437 Thermal Cooling Fan Replacement, Thermal-Cooling Assembly: Schritt 12, Bild 3 von 3

Disconnect cables connected to the motherboard by lifting the flaps up and pulling out.
This is a ZIF connector and needs to have the side flaps flipped up before removal.
The ZIF connector has small clips that need to be pulled up before being pulled out.