Zum Hauptinhalt wechseln

Einleitung

Benutze diese Anleitung, um die Lautstärkereglertasten in deinem iPhone 7 zu entfernen oder auszutauschen. Diese Anleitung ist für die Lautstärkeregler-Tasten an sich, nicht für die elektronischen Schalter darunter.

Wenn du das Kabel zur Lautstärkeregelung ersetzen willst, hilft dir diese Anleitung.

  1. iPhone 7  Lautstärkeregler austauschen, Pentalobe Schrauben: Schritt 1, Bild 1 von 1
    • Vor dem Beginn sollte der Akkuladestand des iPhones unter 25 % liegen. Ein geladener Lithium-Ionen Akku kann bei Beschädigung Feuer fangen oder explodieren.

    • Schalte das iPhone aus, bevor du es zerlegst.

    • Entferne die zwei 3,4 mm Pentalobe Schrauben an der Unterkante des iPhones.

    • Beim Öffnen des Gerätes werden die Dichtungen für den Spritzwasserschutz beschädigt. Halte Ersatzdichtungen bereit, bevor du fortfährst. Wenn du diese nicht ersetzt, ist dein Gerät nach der Reparatur nicht mehr gegen Spritzwasser geschützt.

    Can anyone confirm 7/7P's pentalobe screws have a ring of seal near the screw head?

    Cooper Chase - Antwort

    Confirmed, the screws have a black ring seal around the head.

    rcheing - Antwort

    Can’t get the display front

    Bernadette Pfeifer - Antwort

    From personal experience, I highly recommend before doing this procedure or any other, that you do a backup of your phone (preferably local) in case your procedure goes south.

    ballina5ny - Antwort

    I purchased the repair tools with the replacement battery from iFixit. The tools include a screw driver and three heads none were labeled 3.4 mm. I think the one that fit the pentalobe screws was labeled Y000. The guide should identify the screw driver head supplied by the kit not 3.4mm.

    Mark Lieberman - Antwort

    in the iphone 7 replacement battery kit from iFixit, the screwdriver that fits the 3.4 mm pentalobe screws is labeled P2 (and not Y000)

    Jan-Tijn Oppermann -

    3.4 mm is the height of the screw and is not related to the screw driver code.

    Ahmad Vaziri -

    the screwdriver PH000 does not work i wasted two screws and now they dont have the 4 cross mark they are now a circle, i buyed it all from Paraguay and it doesnt work, had to assembly back the parts because i got stuck like i mention with some screws, well im just going to send to a professional to install, thanks

    Martin Frutos, Nuñez - Antwort

    The bottom screws are Pentalobe, not Phillips.

    Bram Driesen -

    Before starting, I would recommend backing up your Iphone’s data just in case.

    Jon Moylan - Antwort

    If you managed to make it to this section, just send the phone into apple for 50 + 6 dollars shipping. The ribbon cables on the screen are designed to break. I can literally twist on the rest of the cable and it won’t fall apart but there is a diagonal section where it snaps. This is the fault of apple and the fault of ifixit for misrepresenting the fragility of the cables.

    Ryan Huebert - Antwort

    Had to reheat it a few times for a minute each with a hairdryer to get the seal to break after pulling and rocking the suction

    Cynthia Lamb - Antwort

    I’m technically challenged. Is there a premier national service who can professionally install a replacement battery got my 7 +?

    Richard - Antwort

    Do the screws come out in total?

    YVES THEUGELS - Antwort

    Is it the P2 you should use for the bottom??

    YVES THEUGELS - Antwort

    I heated the bottom of the phone with a hairdryer and then used a syringe to put a couple of drops of acetone directly into the bottom two screw holes. I GENTLY pulled on the screen with the suction cup and used the pry tool to GENTLY separate the screen. The sealant is applied around the entire display so be very careful pulling it off so you don’t break the fragile display cables.

    Anthony Scaminaci - Antwort

  2. iPhone 7  Lautstärkeregler austauschen, iPhone 7 öffnen: Schritt 2, Bild 1 von 1
    • Durch Erwärmen der unteren Kante des iPhones lässt es sich leichter öffnen, weil der Klebstoff darunter weich wird.

    • Benutze einen Haartrockner oder erwärme einen iOpener und lege ihn etwa eine Minute lang auf die untere Kante des iPhones, um den Kleber darunter aufzuweichen.

    ¿Cuántos segundos son los recomendados?

    joscarlos91 - Antwort

    Sesenta segundos

    Krutav Shah -

    It is a process. I heated the lower area of the phone with a hair dryer on and off (1min each) about 3-4 times before I was able to get the provided tool in.

    Dan - Antwort

    I suggest using a hairdryer. I used the iOpener for maybe 30 mins to no avail. However, when I used the hairdryer the screen came of much quicker.

    Michael - Antwort

    I totally Mr. Myagi’ed it, by rubbing my hands together until they burned, then held the phone un my hot hands. I did this 5-6 times over a couple of minutes. It was a good zen way to get started!

    Ark - Antwort

    Can a heat gun be used?

    Lee - Antwort

    Absolutely. Just don’t overdo it—the adhesive usually softens up pretty easily. If you are experienced with a heat gun, you’ll have no problem. (If you are inexperienced, it’s easy to cook the display or cause other damage.)

    Jeff Suovanen -

    If i use this process, will iphone 7 still be sealed, water/ splash resist after that?

    Marius Serban - Antwort

    Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

    Angel Hermida -

    Can I use a cpb heating pad to soften the adhesive ? If yes how much time and temperature ?

    davidecongiu - Antwort

    Will doing this compromise the screen protector (Zagg) that I have on my phone?

    Eric Nance - Antwort

    Hairdryer worked for me but I needed to use a razor to pry it open at the bottom then used the spudger

    Gina Torres - Antwort

    Is there a reason why you wouldn’t put the iopener over the entire length of the phone, instead of just the bottom corner?

    BPX - Antwort

    The motherboard is extremely sensitive to heat.

    Neal Reasland -

    Hello can the head damage the id touch bottom?

    After heating opening it stoped working.

    Qrizmasex @ gmail . Com

    aratovski - Antwort

    It definitely can. That happened to me.

    Steve Naylor -

    mine didnt come with a heat pack do i use a hair dryer

    Shy Rose - Antwort

    I just threw a hand towel in hot water, and then stuck it into a plastic bag. Dryers work fine, too.

    hiroo yamagata -

    Thanks for this, the other instructions make it seem SOOOOO simple to open up the case with the suction cup! It actually is hellish. The instruction here about the pre-heating and the required patience really helped!

    hiroo yamagata - Antwort

    For those of you who don’t have an iOpener or a girlfriend, I used a ziplock bag with some instant mashed potato inside. It worked perfectly first time and you can fold the bag around the ID button in order to prevent damage to it.

    You also get to celebrate by eating the mash afterwards, HUZZAH!

    Adrian - Antwort

    🤣 You made my day Adrian, thank you!

    Jicey -

    I found this to be completely useless. It didn’t help at all. I had to use a heat gun instead. Waste of money.

    David Gordon - Antwort

    I’ll experiment with leaving the phone in the sun until the Temperature Warning comes up so the phone tells me when it’s too hot to be safe.

    Maybe it will be hot enough, maybe it won’t—

    edmk5000 - Antwort

    I use a rice pack in the microwave. White dry rice in a sock sown or tied, then microwave (1 minute +/-). The dry rice heats and retains heat for a long time. My kids loved them in in bed during cold winter nights.

    Todd Oeftger - Antwort

    I have changed now Iphone 5 Battery, IPhone 7 front camera & another iPhone 7 rear camera. The instructions along with the comments are really important. Be patient & read them several times. By using your heated gel pack 3-4 times for 2 mins or so on the bottom end near the touch button you will be able to pry with your razor & then you can use your spudger. Thanks for this great guide.

    Kala - Antwort

    I would DEFINITELY recommend to NOT use direct heat (hair drier, etc.) on the phone. I used a hair drier to help heat the phone and ended up damaging the home button (would not work after the replacement and I did not touch or take apart the home button). Note that a damaged home button cannot be replaced so I will end up using the alternative “screen” home button going forward with my phone. Instead I would recommend preheating something else (example - metal / coins / ceramic / beads / glass stones / cookware / etc..) to a warm-to hot (but not burning hot) touch and place the heated items on the IPHONE (or visa versa) to heat and soften the adhesive.

    Ed Scannell - Antwort

    I used 1-gallon Ziploc back and poured 1qt of boiling water into it. I placed my iPhone on a corkboard and the bag on top for 120 sec.

    It worked like magic. I just pooled the screen with the suction cup, and it got loose from the case. No heat damage. Everything works.

    it500 - Antwort

    I placed the iOpener heat bag over the bottom of the phone, disregarding the home button. Now it doesn’t work. All subsequent procedures went well as I was very careful. I should have read all the posts! Protect the home button from direct heat. Fortunately, now using the Assistive Touch feature is better than buying a new phone or replacing the home button.

    Kurt Bee - Antwort

    It’s better to choose an iPhone back case to cover and protect your phone from bumps and scratches. Choosing premium cases is the best option for long-term safety. If you need ***iPhone 7 phone cases*** then you can check them out!

    FLAUNT - Antwort

  3. iPhone 7  Lautstärkeregler austauschen: Schritt 3, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 3, Bild 2 von 2
    • Setze einen Saugheber auf die untere Hälfte der Displayeinheit, knapp über dem Home Button.

    • Achte darauf, dass der Saugheber nicht den Home Button überlappt. Das würde verhindern, dass sich ein Vakuum zwischen dem Saugheber und dem Glas bildet.

    • Wenn dein Display stark gesplittert ist, dann haftet der Saugheber vielleicht besser, wenn du das Display-Glas mit durchsichtigem Paketband abdeckst. Du kannst anstelle des Saughebers auch Panzer-Tape benutzen. Wenn das alles nicht hilft, dann klebe den Saugheber mit Sekundenkleber am zerbrochenen Display fest.

    The glass is completely cracked and the suction cup doesn't work because it gets air in between. any tip?

    Display is glued and doesn't come off.

    support - Antwort

    A wide, single strip of packing tape, well placed, will solve this for you. :)

    Mimic44444 - Antwort

    Last comment works well. Thank you !

    Using packing tape for a cracked screen should be included in the description in Step 3.

    Cracked screen is most probably the reason you are replacing it.

    Arni Benediktsson - Antwort

    I agree that using packing tape for a cracked screen should be included in this steps description. I don’t have wide but turned mine horizontal and that worked great.

    Mary Knapp - Antwort

    Bekomme die Oberschale einfach nicht runter! Trotz mehrmaligem erwärmen durch den iOpener und seitlichen bewegen! Weiß nicht mehr weiter!

    Stephan Lienhard - Antwort

    Wouldn’t that screw up the Touch ID?

    Rexx Havok - Antwort

    The suction cup that is. supplied with the essentials kit doesn’t work that well.

    Laurence - Antwort

    Agreed, the iFixit suction cup was useless. I borrowed one from the sponge holder in my kitchen sink. It lacked a grip so I held it with needle-nose pliers, resting them on a bit of wood to keep pressure off the phone.

    ephraim -

    I am not getting this open at all! Why an I provided with tools that can't help me ??‍♀️

    Bray Joseph - Antwort

    I couldn’t get the bottom to lift first, but the left side did, so I started there and worked my way around the horn.

    selimnairb - Antwort

  4. iPhone 7  Lautstärkeregler austauschen: Schritt 4, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 4, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 4, Bild 3 von 3
    • Ziehe etwas am Saugnapf, bis sich eine kleine Lücke zwischen der Displayeinheit und dem Rückgehäuse bildet.

    • Führe die flache Seite eines Spudgers in diese Lücke ein.

    • Der wasserdichte Klebestreifen, welcher das Display in Position hält, ist sehr stark. Es kann viel Kraft brauchen, um diese erste kleine Lücke zu schaffen. Solltest du dabei Schwierigkeiten haben, wackle das Display etwas auf und ab, um den Klebestreifen zu schwächen, damit du den Spudger leichter einführen kannst.

    This was SO hard for me to do with the spudger. I couldn’t get a gap to insert it because my phone was so cracked (even though I used tape on the front) to get a solid seal with the suction cup. I ended up taking a VERY thin knife and inserting it straight down to make the initial break that allowed me to insert the spudger.

    jessica harlow - Antwort

    I’ve given up using a plastic spudger to try to open any of these phones. I use a metal one with a flat base and a very sharp end…close to a razor. As long as I’m careful, it won’t slip and scratch the base. It’s much easier than using these plastic spudgers.

    mcr4u2 -

    I confirm that the plastic spudger it’s not the best tool for this operation. I suggest to use a larger metal tool like a “Jimmy” or “iSesamo open tool” (I used the first one)

    Cristef -

    Im trying to get the screen off right now and my phone is not cracked and its still a pain

    Jordon Johnson - Antwort

    Using a blow dryer was extremely helpful and using the suction cup towards one of the lower edges was also helpful

    Jordon Johnson - Antwort

    This is not working for me. How long does the heat need to be applied? Still trying right now…. =/

    Chris Gallego - Antwort

    Apply hair dryer for at least 1 minute. I inserted the tip end of a thin mini screwdriver and with some force, pryed it open and inserted my plastic spudger to continue the separation process. It worked, just be patient.

    Please wear protective glasses! My iPhone glass was severely cracked, when separating the glass a corner area of broken glass exploded in my face. Apply transparent tape over the broken glass to contain the shards.

    amberron - Antwort

    I second Jessica’s January 8 comment.  I just finished a battery replacement on my iPhone 7 and this step was the most nerve-wracking part.  I ended up using a sharper (but not razor-sharp) metal object to get this done with confidence (tried the spudger and guitar pick but not thin enough).  The tool I used was the exact duplicate of what iFixIt calls “iSesamo Opening Tool” in their tool selection.  I did the heat up with a hair dryer (after attempts with an iOpener hot pad) and the secret (as Jessica also noted)  was to not use the angle of attack shown in the pictures, but to push it in more vertically along the bottom edge while pulling up on the suction cup.  From there you can easily lever the tool to the lower angle-of-attack (as shown in the picture).  I actually used the metal tool for most of the perimeter as well, just don’t go deep (you don’t need to).  Notes: my display was intact, and I was able to pull up fairly hard with a glass screen protector still on it.

    Ted - Antwort

    This is frustrating. I heated the lower edge with a hair dryer for 1 min on high about 3-4 times. In between each heat cycle, I rocked the suction cup back and forth. I was eventually able to create significant space for the provided tool. This takes a lot of patience. Once the space was created, it was very easy to remove the screen.

    Dan - Antwort

    use a fingernail, then the blue tool, then the spudger

    Therese Peffer - Antwort

    The iOpener worked just fine for me. Had to keep it on for a few minutes. I also was able to get the suction cup seal right close to the edge, over top of the home button for added leverage. Used the blue tool and transitioned to the spudger. Slow, steady pressure…and patience. ;)

    johnhall918 - Antwort

    Unable to open an iPhone 7 display assembly. Used gell pack at 150 degrees F. The phone wouldn’t budge when I used the iFixit suction cut. Part of the problem is that the cup doesn’t adhere for long before it looses suction. I suspect it would work better on unbroken glass, but that doesn’t help me now. After spending a lot of time at this, I changed heating methods to a hot air heater. I raised the temp of the bottom end of the phone to, ultimately, 175 degrees, and used a variety of tools to try to pry the glass apart enough to get a spudger (or anything) in, but it didn’t even lift enough for a double-edged razor blade to get in. I’ve been trying this for hours now, and about to give up and throw a lot more money at this to have a service perform the work. I figured that 175 was as high as I should need to go to soften the adhesive without damaging the electronics. Should I have gone higher? I see no mention of measured temps in any instructions or comments.

    ted - Antwort

    Have you tried applying tape to the broken screen? This will help a lot with keeping the suction cup on it.

    Christian Groothuis -

    It doesn’t need to get very hot; pulling up on the display is mainly what does the trick. Make sure the two pentalobe screws have been removed and then try the tricks in this step. If all else fails, superglue the suction cup to your display and let it cure, and then pull. Keep in mind you only need a tiny gap to insert a plastic pick and start cutting the adhesive. Good luck!

    Jeff Suovanen -

    Just a question. After this operation the impermeability function was compromitted?

    bentek86 - Antwort

    The trick I found, was to add packing tape right across the bottom over the home button then use hairdryer on the end, then suction cup on the very bottom and it lifted enough to get a gap. No one mentioned how it would be impossible to handle the phone after the hairdryer ;)

    Andrew Lansdowne - Antwort

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Antwort

    I used a hair drier while lifting up at the same time until I could get the too inside. The seal is pretty finicky. Just take your time and you should be fine. Work the hair drier and the tool all the way around before lifting the screen up and off. There will likely be sealant stuck between the screen and phone. You can just break it with the tool.

    Ray Bieze - Antwort

    This step was impossible for me despite using a blow dryer and having no cracks on the screen. I finally took it to a local repair place and had them do battery replacements for two iPhone 7’s. The girl let me watch her do it. She used a razor blade (just until she had a small opening that she could hold open with her fingernail) and confirmed that she too would have difficulty opening it with a plastic tool and suction cup. The plastic tool was great for prying the rest of it open once a crack was there, but she said she would never try to use that as the tool to initially open it. The tools provided for initially prying open the screen are inadequate.

    Chad Twedt - Antwort

    Hopeless - no chance to get the screen off without any damage. No matter what tools, heat etc.

    Anatole Beams - Antwort

    I second what others have said, definitely use a razor blade to break the seal! Heat helps some, but too much direct heat is bad for the screen. Would have been impossible if I hadn’t read the comments, thanks everybody!

    Kit - Antwort

    Use extreme caution on this step. I was just replacing my battery and now i’m buying a new screen. The screen was very stuck, I pulled to hard and it popped off suddenly, completely destroying the screen.

    moose - Antwort

    When the right heat is reached, the easiest way is to use a metal iFlex to create the initial gap, then insert the Jimmy or iSesamo next to it so the gap gets bigger, at this point you can get in with the flat edge of a plastic spudger and slowly slide it in the borders to cut the adhesive. You will still need to force a bit the upper end to separate the screen by pulling it down while keeping up the screen, and twist to the right. I hope this is clear enough. Never apply too much strength too quickly anyway.

    Stefano Restuccia - Antwort

    I used the short blade of my swiss knife to make an initial opening. Using the sharp edge, inserting about 1 mm straight down and twisting down into a 45° angle. Then I was able to insert the spudger.

    John van de Loo - Antwort

    This is a difficult step. Fortunately, I had another suction cup from an earlier repair available, so I applied one to each side of the phone. After warming with a hair dryer, I was able to pull the two suction cups far enough away that another person could easily insert the spudger.

    The third hand was essential.

    Mark - Antwort

    I found this tactic to be the best solution for us. I used two suction cups, one on each side of the phone, and another set of hands to get a pry tool under the display. We still had to take our time prior while heating the adhesive, but were able to pry the display fairly easily using the two suction cup method.

    Lucas -

    It was a really excruciating process of heating, lifting with the suction cup, trying to slide in the spudger/pick, and repeating the process for 20 times or so. But in the end, my patience paid off!

    hiroo yamagata - Antwort

    I used a hair dryer, then used a safety razor blade parallel to the bottom edge to push straight down (from the glass side, towards the back) while lifting with the suction cup. I wiggled the blade (top to bottom) while pressing down gently, until I saw a gap that would accept the spudger. It did not take much force on the blade or much wiggling, just patience.

    Gene Merritt - Antwort

    Followed Gene’s approach with heat and a razor blade. I was nervous, but went slow; it was very easy and effective. Great tip. Just be patient and don’t rush yourself.

    Michael J - Antwort

    I would skip right to using a single edge razor blade and a hair dryer to create the gap needed for the spudger.

    Logan Brown - Antwort

    Think plunging the toilet - it did not work for me for a long time. the suction cup would not stay held on a long pull. I found that tiny push-pull repeated motions, reseating the suction cup with each push slowly overcame the adhesive, and contributed heat :). I had it after about 50-70 cycles

    Andrew Balanda - Antwort

    seconding this comment from Ted ~~~ “the secret (as Jessica also noted)  was to not use the angle of attack shown in the pictures, but to push it in more vertically along the bottom edge while pulling up on the suction cup.  From there you can easily lever the tool to the lower angle-of-attack (as shown in the picture).”

    natjpollard - Antwort

    I echo what everyone is saying here, the spudger just isn’t good enough for this and neither is a pick. The razor is the best way to go. I tried using a very sharp penknife blade and managed to damage my LCD (somehow!) and the bezel so I ended up having to buy a new screen display as well as a new battery. Think twice before doing this. Be prepared to shell out for a new screen just in case it goes wrong. You’ll also need the heat gun (the iopener was useless). If you do need to buy a new screen, make your life easier and get one with the speaker, forward-facing camera, home button, etc., already attached (you can then replace the home button) or you’ll end up having to transfer all these from your old display.

    David Gordon - Antwort

    I finally got the screen up but shattered it in the process. I was replacing it anyway but if the screen is not what you’re replacing, take EXTEME caution. The suction cup and spudger were not working for me to get it started. Thanks to the comments, I used a razor blade and a heating pad and went back and forth, back and forth, between heat and pressure from the blade. Once you get a gap, the spudger works great and the screen comes up easy.

    Nick Nave - Antwort

    The suction cups that iFixit sells are crap. They don’t stick at all. Glass on the phone is pristine.

    Nick - Antwort

    More feedback on this “guide”:

    “Pull up on the suction cup.” What does this mean? If I just pull up on the suction cup (with a real one that actually sticks) it just lifts the phone off the table. You need a description of what you are pulling against. Do I try to hold the frame of the phone? Do I try to stick something in the lightning port to pull against? Do I try and get something against the edge of the rounded metal on the edge of the phone (this usually just slips off). What am I pulling against???

    Nick - Antwort

    I found a combination of iOpener, suction cup and razor blade, all applied at the same time, worked for me and I didn't need to use a hairdryer.

    Peter Gray - Antwort

    Dumbly, I thought that with the Spudger I'd had to hold the phone from the charging hole while pulling the screen. .. In the end I inserted the two ends of the tweezers(bends the tweezers and may damage it) in the screwdriver holes and pushed the screen out upwards so that I could insert the sharp side of a knife.

    Claudiu Cezar - Antwort

    This was my first iPhone battery replacement and I can say this was the hardest part.

    Be wise, go for a hair dryer and heat up the phone bottom (long enough). iOpener did not work at all for me. Heat up, use the suction cup and push the opening pick under the frame as soon as you see movement along the frame.

    Then use the spudger to wander around the whole frame (leaving the pick where it is). Done!

    Guenter - Antwort

  5. iPhone 7  Lautstärkeregler austauschen: Schritt 5, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 5, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 5, Bild 3 von 3
    • Ziehe das Werkzeug nach links, entlang dem unteren Rand des iPhones.

    • Drehe das Werkzeug, um die Lücke zwischen dem Display und dem Rückgehäuse weiter zu vergrößern.

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Antwort

    I used a hairdryer and a razor

    Gina Torres - Antwort

    The photos are a con. You cannot get a spudger in unless you can lift the screen. You cannot lift the screen because of the adhesive. Using a anything metal will damage the paintwork or the glass edge.

    Anatole Beams - Antwort

    I agree, these guides are half imaginary idealism it seems. A thin metal edge pushed vertically down just a fraction of a mm will cause the adhesive to weaken better than any amount of heat, but affects the final appearance sadly.

    Jesse de Vries - Antwort

  6. iPhone 7  Lautstärkeregler austauschen: Schritt 6, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 6, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 6, Bild 3 von 3
    • Ziehe das Werkzeug von der unteren Ecke die linke Seite hinauf zu den Lautstärketasten und dem Stumm-Schalter.

    • Heble nicht am oberen Rand des iPhones, sonst riskierst du es, die Plastikclips zu beschädigen, mit denen das Display befestigt ist.

    Be VERY careful on this next step going up the right side of the phone. There is a ribbon cable 1/3 of the way up from the bottom that is very close to the edge. Do NOT use the blue triangle!!!! Just lightly rotate the spudger to get separation on the edge.

    Timothy Varvais - Antwort

  7. iPhone 7  Lautstärkeregler austauschen: Schritt 7, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 7, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 7, Bild 3 von 3
    • Führe das flache Ende eines Spudgers in die rechte untere Ecke des Geräts ein.

    • Drehe den Spudger, um die entstehende Lücke zwischen der Displayeinheit und dem Rückgehäuse zu vergrößern.

    • Ziehe die flache Seite des Spudgers entlang der rechten Seite nach oben, um den Klebestreifen zu lösen, der das Display fixiert.

    • Schiebe den Spudger nicht tiefer als den Klebestreifen ein, damit die empfindlichen Flachbandkabel am rechten Rand unbeschädigt bleiben.

    Shoot. I broke the sensitive ribbon cable because I didn’t quite understand what the instructions meant with not to insert the spudger further than the adhesive. It means depth wise, not up the side. Sigh.

    Leo Hwang - Antwort

  8. iPhone 7  Lautstärkeregler austauschen: Schritt 8, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 8, Bild 2 von 2
    • Ziehe am Saugnapf, um das Display anzuheben und das iPhone zu öffnen.

    • Hebe das Display nicht höher als bis zu einem 10 Grad Winkel, denn rechts sitzen Flachbandkabel, welche das Display mit dem Logic Board verbinden.

    do not pull up pull sideways it will brake

    Riley Patterson - Antwort

    Made this mistake

    rachael.grime - Antwort

    Somehow my phone turned itself back on during the opening. Scared me a little, like a patient coming out of anesthesia during the operation. I was able to turn it back off. Gotta be more careful where you grab this thing.

    Bryant Larsen - Antwort

  9. iPhone 7  Lautstärkeregler austauschen: Schritt 9, Bild 1 von 1
    • Löse den Saugnapf vom Display-Glas und nimm ihn ab.

    very nice

    iPhone 7 back cover

    http://WHITEWINGS.IN/

    Vikash Kumar - Antwort

  10. iPhone 7  Lautstärkeregler austauschen: Schritt 10, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 10, Bild 2 von 2
    • Fahre mit einem Opening Pick am oberen Rand des iPhones, zwischen dem Rückgehäuse und dem Front Panel entlang, um den restlichen Klebstoff, der das Display hält, zu lösen.

    • Achte darauf, nicht die Plastikclips am oberen Rand des iPhones zu beschädigen.

    The plastic clips mentioned are on the top of the screen being replaced… so not sure why it matters not to break them. Trick here was to pull the screen downwards to open a gap at the top and then insert as shown and raise to break the seal.

    Andrew Lansdowne - Antwort

    This is relevant for other guides than the display replacement guide.

    jvalaamo -

    プラスチックのクリップという

    表現に混乱しました。

    上部に食い込んでいる

    差し込みのことだったんですね。

    下に引っ張ったら抜けました。

    情報ありがとうございました。

    MARU - Antwort

    The opening pick is packaged with the battery, not the tools, so I didn’t find it until I was past this step. Made do with careful use of the spudger and a lot of wiggling the display to break the glue.

    ephraim - Antwort

  11. iPhone 7  Lautstärkeregler austauschen: Schritt 11, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 11, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 11, Bild 3 von 3
    • Ziehe die Displayeinheit etwas von der oberen Kante des Telefons weg, um die Clips zu lösen, die sie am Rückgehäuse halten.

    • Öffne das iPhone, indem du das Display von der linken Seite her aufklappst, wie die Rückseite eines Buches.

    • Versuche nicht, das Display schon komplett zu entfernen, da empfindliche Kabel das Display immer noch mit dem Logic Board verbinden!

    I just broke the cable to the battery!

    No Bama - Antwort

    same dude im such a freak lol omg haha

    Aiden Polaski - Antwort

    Are there replacements ribbons?

    Blax Bently - Antwort

    Has anyone else noticed very small squares of rubber with a circle cut through it (I think they fall off into the phone when dismantling)?

    I just replaced my screen and worked out that these are actually a wee pocket that slips over the pentalobe screw holes on the replacement screen. I’m not sure if it’s an additional water resisting mechanism or if it’s to add additional traction for the screws

    richarddillon - Antwort

    Thanks, I was wondering where those were from!

    Albert -

    Same, I only had one fall out and I had no idea if important, and didn’t re-add - because I wasn’t sure where it fell from - but it was definitely from the home screen button….watch it be important. -__-

    Nicole Crome -

    I just broke cable connecting camera and earpiece speaker to logic board. Be careful with it.

    Natan Haładyn - Antwort

    This section is missing a critical step - to lay some Post-It notes or something below the right half of the phone when you swing it open, so the ribbon cables don’t get sliced by the sharp edge of the phone case. I broke the Home Button ribbon cable because there was no strain relief when I laid it open.

    neila - Antwort

    I also broke the home button cable and now I have to use assistive touch.

    Laurencio Gonzalez - Antwort

    Keep the suction cup on the display to keep it propped up while you disconnect the ribbon cables.

    minimalist - Antwort

    I broke the short ribbon cable that attaches underneath the lower connector bracket. Be SURE when you lift the display, you do it from left to right. I thought I had the phone oriented correctly in my hand, but I was mistaken.

    John Murray - Antwort

    Put the suction cup on the right side of the middle of the screen when you rotate it up and out. It serves as a nice stand to take the pressure off the connectors.

    Ray Bieze - Antwort

    no mention of what you do once u open the book. are the ribbons long enough to lie flat  or do we have to keep screen raised while removing screws,, like when we hold screen up 45 degrees while removing 5 screw plat when at top of phone. I only realised how fragile the ribbons are and how important it is to use suction  cup to rest screen on an angle so ribbons don't stretch or cut on frame.

    thanks for the above comments and probably the most important section. I just hope I closed t before I fdid any damage. its lke the fragility of iPhone 3’s all over again.

    scallyteacher - Antwort

    I just broke one of the cables… yeah, it is not nice… I’m lucky in the sense the screen is still working, but the button is not.

    Trying a cheap screen on Ebay (that contains the cable) do 20$, after that, it’s a new cellphone…

    Vincent Poirier - Antwort

    Be EXTREMELY careful when you lift up the screen. I broke 3D touch cable, and the home button stopped working. Had to replace the whole display.

    Sizun Cho - Antwort

    Attention ! J’ai cassé la nappe de la caméra avant !

    arnauldjouanny - Antwort

    • Entferne die vier Tri-Point Y000-Schrauben, die die Abdeckung der unteren Anschlüsse befestigen, sie haben folgende Längen:

    • Drei 1,2 mm Schrauben

    • Eine 2,4 mm Schraube

    • Passe während der ganzen Reparatur gut auf die Schrauben auf und sorge dafür, dass sie genau an ihren alten Platz zurück kommen, sonst kann das iPhone beschädigt werden.

    Ahhh shoot! accidentally ordered tri-wing vs tri-point (must have just looked for y000).. It seems they only did this to annoy repair folks because not everything is tri-point on the phone...

    Steve - Antwort

    These screws just spin for me. They don't back out, but the heads aren't stripped either. I've tried applying backpressure to help lift the screws, but no luck

    Jeff Hurst - Antwort

    The Y000 took out one of the screws but not the other 3. I even tried the PH000 as suggested but nothing.

    dbright - Antwort

    What driver do I need to remove these screws i’m stuck

    Nasser Nader - Antwort

    i cant use, the Y000 it isnt working.

    joscarlos91 - Antwort

    What if I stripped a screw what do I do??

    Jacob Ramos - Antwort

    Yep, only the 2.4mm came out, other 3 won’t budge, and worried I’ve stripped the heads. Anyone got any ideas?

    Stephen Babbage - Antwort

    It’s the screwdriver bit that is the problem. I had the same issue with 2 Y000 bits not grabbing the screw properly. I fixed it by using a small 3 sided file to slightly grind the groves in the Y000 bit just a bit deeper. Then the bit worked like a charm on these screws.

    Jim Staples - Antwort

    Use Y000 on all 4. U have to be very sensitive on the 1.2mm screws. Put the bit in the screw, put the left pointing finger on top of the screwdriver and turn the driver carefully to the right until you feel a “bump”, thats the trick :-), then you are able to screw the screw out.

    Magne Eivindson - Antwort

    For me the key here was a LOT of downward pressure to ensure the Y000 bit caught in the screw. Not sure i can describe how much exactly, but is was significant. Otherwise the bit would not catch.

    Erik Fredriksen - Antwort

    What do I do if I Stripped one of them?

    Adam Corral - Antwort

    Can’t get them removed what to do ?

    cowling_luke - Antwort

    Managed to get the central one out. The upper one won't move, the lower one I've popped out with some force. This allows you to rotate the cover enough to unplug the various bits. Not ideal, but works. I've tried applying a lot of pressure, using the tighten/ loosen method, but the heads have just got mashed… no wonder Samsung are now No1, sigh…

    jimpoolio - Antwort

    You need to be careful when just rotating the cover as you can accidentally slice through the two black antennas! You only need to nip them…As you can tell I have done this in the past :/

    Kyle Webb -

    The first, longer screw came out fine, but the other three wouldn’t budge, regardless of more/less pressure or a slight angle or anything. I finally filed down the tip of the Y000 bit ever so slightly, and then it worked. Hope this helps someone.

    Harmony - Antwort

    Filing down the bit worked for me. The tip about putting an index finger on the end of the screwdriver handles and then turning gently until it clicks into place was very helpful! Using these 2 tips I didn't need much downward pressure. Screws are out in a few turns.

    Chris Bennett - Antwort

    If you can’t get the bit to grip the screw properly, you can use a little bit of the water-proof sealing between the bit and the screw. That worked for me. Hope this helps anyone.

    jvalaamo - Antwort

    Mine came out easily. I placed the screws in the area where the bit goes in my kit so I can keep track.

    Gina Torres - Antwort

    I used a bunch of medicine cups to track my screws. You need like 12 if you want them all in cups. I ran out. There are so many different sizes that literally vary by 1mm. The tolerances on these things are tight.

    Ray Bieze - Antwort

    I use a 28 day pill box and keep every screw separate and reburn to exact slot because they all vary in length, width and can really damage u phone if too long and nt secure if to small.  use a magnetised screwdriver,  or make the cheap freebees magnetic for a short period by rubbing it up an a magnet. lol

    scallyteacher - Antwort

    Absolutely ridiculous had to go get a different one just stupid

    mark golling - Antwort

    I couldn’t get the lowest one out and just turned the metal bracket out of the way and replaced battery.

    qwerty77x - Antwort

    Was able to get the outer bracket screws out using fine needle nose pliers 90 degrees straight down for the outer ones by pressing down a little and using medium gripping force. Had to take these out first before i could use tweezers on the middle one, for which I had to use tweezers to hold the screw, then rotating the bracket (not the screw) counter clockwise a few mm many times over to slowly unscrew it 1/32th of a turn at a time, repeat. (this loosened middle screw). Think ‘rotating bracket 3minutes/degrees counterclockwise at a time while holding screw in place.) You are gonna need really small/fine pliers and tweezers for this because the heads are countersunk into the bracket.

    Galen Wollenberg - Antwort

    The top screw in the step was much longer than 1.2mm. It has the same head as the 1.2mm, but different than the 2.4mm. It’s good to keep track of where they came from.

    All are so small that I thought I’d lost one, when it was still sitting in the phone.

    Mark - Antwort

    To help tell if the screw is turning, put a small dot from a marker on the head of the screws.  This helped me to know I wasn't just stripping the head.

    Darren Thibodaux - Antwort

    try heating the iPhone with a hairdryer or a bag of rice or about 60 degrees in an oven for 3 minutes . It has worked for me. If the screws don’t come out while hot the will come out as the iPhone cools.

    David Howard - Antwort

  12. iPhone 7  Lautstärkeregler austauschen: Schritt 13, Bild 1 von 1
    • Entferne die Abdeckung der unteren Anschlüsse.

    my battery cable connector was stuck to the bottom of this metal bracket plate so be careful when you lift it off

    Josh Martin - Antwort

    This may have been intentionally done by Apple to make sure the battery gets disconnected before any other connector is disconnected. So always make sure to disconnect the battery before disconnecting and reconnecting the connectors for the display.

    Oscar Moreno - Antwort

    So…I forgot to put this bracket back on when reassembling. Now I’ve adhered the display to the case and don’t have another adhesive strip…so I’m wondering: what purpose does this bracket serve? The phone is powering on and seems to work okay.

    Am I going to run into trouble with this bracket missing?

    Ian Fritz - Antwort

    Well, that didn’t last long. The phone shuts down without warning. So I guess that plate is important…

    Ian Fritz -

    I also forgot to put the battery shield in, and adhered the display. I’m tempted to leave it like that. However, your negative experience is a good data point telling me to not be cheap.

    Ordered a new adhesive , under $2 shipped from eBay.

    Yishai Sered -

    Thanks, Josh Martin! Mine was stuck too, so I lifted carefully.

    Cynthia Lamb - Antwort

  13. iPhone 7  Lautstärkeregler austauschen: Schritt 14, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 14, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 14, Bild 3 von 3
    • Mit der Spitze eines Spudgers kannst du den Stecker der Batterie vom Anschluss auf dem Logic Board heben.

    • Biege das Kabel leicht nach unten, um zu verhindern, dass es mit dem Anschluss in Berührung kommt und das Telefon mit Strom versorgt.

    Was kann passieren wenn man diesses Kabel vergessen hat zu entfernen `?

    Julian Eltrich - Antwort

    Reconnecting the battery poorly can cause the iPhone to appear to be properly powered and functional, but then suffer a reboot loop.

    I had difficulty after a screen replacement, and the Console app on my Mac showed that the ‘thermalmonitord’ process was throwing lots of errors from not getting any sensor readings from the battery. It would never charge past 1% and just kept rebooting.

    The contacts on this conector looked fine so even though I had reseated this connector several times already, I reconnected it very firmly using my thumb and a spudger to really press all the corners and middle and really gave it a good massage and then finally it showed the normal dead battery screen and started properly charging and eventually booted back up to normal functionality.

    It seems the battery has to be able to transmit data to the phone to say it’s not overheating or iOS will not allow any current into the battery to recharge it, and the kernel will panic from the null readings and just reboot over and over again.

    jason - Antwort

    In my case, the battery connector was attached to the bracket. We just left it connected bracket when we pryed it up.

    Dave Miller - Antwort

    Reconnecting the battery connector was a bit difficult in my case. The cable that comes out of the battery was a tiny bit too long, or that I placed the battery a bit too high (i.e., too close to the top of the phone). It took me several frustrating minutes of fiddling with the connector for it to sit right into the socket. I was not sure if that was connected correctly but, alas, the phone came back to life when it was turned back on.

    Tomoharu Eguchi - Antwort

    VERY IMPORTANT NOTE: Please READ the reply here by jason.

    It is very easy to knock off or nudge the little pins near the battery socket, see https://guide-images.cdn.ifixit.com/igi/... and https://guide-images.cdn.ifixit.com/igi/....

    Those pins are the data lines to extract battery info: temperature, charge, etc. If you accidentally nudge/knock off them the phone could appear to work normally, even for a few days. But then you will start getting wrong battery reads and then after that it may suffer a reboot loop. If you enter settings > privacy > analytics & improvements and you scroll down you will find panic errors from thermalmonitord that there are missing sensors (TG0B or TGXXX) and you will have to micro solder them. DO NOT NUDGE THEM and double check the socket connector when reconnecting the battery.

    PJM - Antwort

  14. iPhone 7  Lautstärkeregler austauschen, Display Einheit: Schritt 15, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen, Display Einheit: Schritt 15, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen, Display Einheit: Schritt 15, Bild 3 von 3
    • Bevor du in diesem Schritt ein Kabel ablöst oder wieder verbindest, musst du den Akku abtrennen.

    • Nutze das Flache Ende deines Spudgers oder deinen Fingernagel, um die Anschlüsse des Flachbandkabels am unteren Ende des Displays zu lösen.

    • Um die Stecker wieder zu verbinden musst du diese unbedingt erst an einer Seite, dann an der gegenüberliegenden herunterdrücken. Drücke nicht in der Mitte, da sie sich verbiegen und im schlimmsten Fall funktionsunfähig werden können.

    • Wenn du nach dem Zusammenbau deines Smartphones ein leeres Display, weiße Streifen, teilweisen oder kompletten Ausfall des Touchscreens hast, dann versuche nochmals diese beiden Kabel abzutrennen und sorgfältig wieder anzuschließen. Achte darauf, dass sie wirklich fest sitzen.

  15. iPhone 7  Lautstärkeregler austauschen: Schritt 16, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 16, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 16, Bild 3 von 3
    • Entferne die beiden 1,3 mm Kreuzschlitzschrauben #000, mit denen die Abdeckung über dem Stecker der Frontsensoreinheit befestigt ist.

    • Es können auch Y000 Schrauben sein. Apple hat etwa in der Mitte der Produktionszeit auf Y000 umgestellt.

  16. iPhone 7  Lautstärkeregler austauschen: Schritt 17, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 17, Bild 2 von 2
    • Entferne den Stecker der Display Einheit von seinem Anschluss auf dem Logic Board.

    • Der Stecker sollte nicht mittig festgesteckt werden, um ein Verbiegen zu vermeiden.

  17. iPhone 7  Lautstärkeregler austauschen: Schritt 18, Bild 1 von 1
  18. iPhone 7  Lautstärkeregler austauschen, SIM-Karte: Schritt 19, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen, SIM-Karte: Schritt 19, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen, SIM-Karte: Schritt 19, Bild 3 von 3
    • Führe das SIM-Auswurfwerkzeug oder eine Büroklammer in das Loch am SIM-Karteneinschub.

    • Drücke das Werkzeug in das Loch, um den SIM-Karteneinschub auszuwerfen.

    • Dies erfordert mehr Kraft als man denkt. Achte darauf, dass das Werkzeug korrekt ausgerichtet ist, damit der Auswurfmechanismus nicht beschädigt wird.

    • Entferne den SIM-Karteneinschub aus dem iPhone.

    • Wenn du die SIM-Karte wieder installierst, vergewissere dich, dass die Karte richtig herum in den Karteneinschub eingelegt ist.

    Received a sim card tray from IFIXIT for my iphone 7. I can’t seem to get it to close flush no matter how hard I try. Any suggestions?

    AJ Dereume - Antwort

    Why would it require a significant amount of force? Is it because the iPhone 7 is water resistant? When I removed my tray it was like it was stuck in goop inside the phone and the tray had a glue like sticky substance on it? It did not ‘click’ back in smoothly like my other iPhones, I had to push it against the ‘goop’. Is this normal for iPhone 7??

    Rebecca Diakun - Antwort

    I used the tip of the super pointy tweezers, and it worked well.

    Cynthia Lamb - Antwort

  19. iPhone 7  Lautstärkeregler austauschen, Logic Board Anschlüsse: Schritt 20, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen, Logic Board Anschlüsse: Schritt 20, Bild 2 von 2
    • Benutze das flache Ende eines Spudgers, um den Anschluss der Rückkamera zu trennen.

  20. iPhone 7  Lautstärkeregler austauschen: Schritt 21, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 21, Bild 2 von 2
    • Entferne die folgenden Kreuzschlitzschrauben, mit denen die Halterung der Rückkamera am Rückgehäuse befestigt ist:

    • Eine 1,3 mm Schraube

    • Eine 2,5 mm Schraube

    I couldn’t get my 1.3mm screw out. It’s not required thankfully as you can just bend the cover up and out of the way to complete the rest of the steps.

    Ray Bieze - Antwort

    i removed them with PH000

    Flavien - Antwort

  21. iPhone 7  Lautstärkeregler austauschen: Schritt 22, Bild 1 von 1
    • Entferne die Halterung.

  22. iPhone 7  Lautstärkeregler austauschen: Schritt 23, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 23, Bild 2 von 2
    • Heble den Stecker am Antennenkabel direkt links neben dem Rückkameramodul mit der Spudgerspitze hoch und löse ihn ab.

    There is one Step missing before removing the flash light cable: Remove Camera cable, right?

    Achim Breidenbach - Antwort

    I broke this and can’t find it on amazon. Is it part of the volume control flash connector? If not, can you send me a link on where to find this connector,…and possible instructions on how to replace?

    Daniel Buhler - Antwort

  23. iPhone 7  Lautstärkeregler austauschen: Schritt 24, Bild 1 von 1
    • Entferne die beiden 1,2 mm Tri-point Schrauben, mit denen die obere Kabelhalterung befestigt ist.

    these are too tight cant get rid off them from y000

    Narendra Mane - Antwort

    ok with Y000 from pro tool kit

    Flavien - Antwort

    Had to push down to get the Y000 in place

    Cynthia Lamb - Antwort

  24. iPhone 7  Lautstärkeregler austauschen: Schritt 25, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 25, Bild 2 von 2
    • Entferne die obere Kabelhalterung.

  25. iPhone 7  Lautstärkeregler austauschen: Schritt 26, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 26, Bild 2 von 2
    • Verwende das flache Ende eines Spudgers, um den oberen Kabelstecker zu trennen.

    Este cable q funciona tiene porfavor lo desconecte y funciona normal

    Johnny Bolaños - Antwort

  26. iPhone 7  Lautstärkeregler austauschen: Schritt 27, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 27, Bild 2 von 2
    • Entferne die vier Kreuzschlitzschrauben, mit denen die Wlan-Antenne befestigt ist:

    • Drei 1,2 mm Schrauben

    • Eine 1,7 mm Schraube

    I lost one of these 1.2 mm screws. Will that affect the signal reception?

    Bethany Knaebel - Antwort

    There is another screw connecting the antenna to the case.

    tbaiello - Antwort

    How do you open the 1.7mm screw? LOL

    Kyle Victor - Antwort

    The screws are not threading in for some reason. I measured the screws to be exactly 1.2mm with a caliper.

    Loopy75 - Antwort

    Yes there are 4 x screw 3 x 1.2mm and 1x 1.7mm securing the antenna to the case

    ANDREW - Antwort

    Yes : 4 screws and not 3 !!

    sirthomasnardin -

  27. iPhone 7  Lautstärkeregler austauschen: Schritt 28, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 28, Bild 2 von 2
    • Entferne die linke obere Antenne.

    ** also remove the small Phillips screw fastening the WiFi antenna to the top rear casing of the phone

    iBroke - Antwort

  28. iPhone 7  Lautstärkeregler austauschen: Schritt 29, Bild 1 von 1
    • Entferne die folgenden Kreuzschlitzschrauben:

    • Eine 1,3 mm Schraube

    • Eine 2,2 mm Schraube

  29. iPhone 7  Lautstärkeregler austauschen: Schritt 30, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 30, Bild 2 von 2
    • Entferne die Halterung.

    What's this bracket called

    Cris Velasquez - Antwort

    %#*@, lost that part during the job, thought it’d be alright without it. Couple days later figured out NFC doesn’t work anymore. Any ideas on where to get this part from, colleagues?

    azowux - Antwort

    • Entferne die 2,2 mm Abstandsschraube von der Erdungsklammer.

    • Abstandsschrauben werden am besten mit einem Schraubendreher für Abstandsschrauben entfernt.

    • Zur Not geht es auch mit einem kleinen Flachschraubendreher, du musst dabei aber aufpassen, dass du nicht abrutschst und umliegende Bauteile beschädigst.

    What bit is this? The link doesn’t use the same name.

    Mike Moran - Antwort

    I didn’t even have an eyeglass repair kit flathead, so I hit the end of a paperclip with a hammer to make a flathead, and it works!

    Ark - Antwort

    I hate getting the deep into a repair to find there’s a tool missing. This bit should be part of the toolkit!

    Ark - Antwort

    Its in the toolkit now. Looks like a Philips head but up close the end is squared off with a point in the middle.

    Jesse de Vries -

    I received two boxes - one box contained the repair part, the other was the tool kit. I only opened the tool kit before disassembling the phone. The standoff screwdriver bit was not in there. Neither was the guitar pick. I used a real guitar pick and a small standard screwdriver from my toolbox. When I was ready to reassemble, I opened the repair part box and guess what was in there - the standoff screwdriver bit and guitar pick. So, I guess if you just order the part it will come with (at least) those two tools. The tool kit contains tweezers, suction cup, three screwdriver bits (tri-point, pentalobe, and phillips) and screwdriver handle, a long black spudger with a flat end and a pointy end, and a smaller, thicker spudger with a wide, flat ends.

    bronyaur - Antwort

    The flat end of the spudger works a treat too.

    Robert Trammel - Antwort

    Thank you, bronyar. Since there is a box labeled “Repair Tools”, I never would have looked in the parts box for tools. I was able to use the standoff tool to takie the phone apart, not just to put it back together.

    Mike Ruzicka - Antwort

    I used standoff bit for iPhone from my pro tool kit

    Flavien - Antwort

  30. iPhone 7  Lautstärkeregler austauschen: Schritt 32, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 32, Bild 2 von 2
    • Mit einer Pinzette kannst du den Endungswinkel des Logic Boards vorsichtig aus dem Weg biegen.

    I accidentally broke the grounding bracket, is it very important to get a new one to replace? as I can't seem to find them for sale anywhere

    Mustifa shah - Antwort

    I also broke it. Did your phone work after?

    Did you find a replacement?

    Ben Schorr - Antwort

    Did your phone work ?

    Emin -

    also broken does it work without?

    Emin - Antwort

    I broke mine while doing this step. A bit confusing. You’re just supposed to bend it out the way, not pull on it entirely. Will the phone still work without this?

    Chandler Forrest - Antwort

    $@$*, i broke the grounding bracket

    Z1xus - Antwort

    I just didnt bend this one.. Ill tell you how it went

    Lauren Campbell - Antwort

  31. iPhone 7  Lautstärkeregler austauschen, Logic Board: Schritt 33, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen, Logic Board: Schritt 33, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen, Logic Board: Schritt 33, Bild 3 von 3
    • Hebe die beiden Antennenverbinder mit der Spudgerspitze aus ihren Sockeln auf dem Logic Board.

  32. iPhone 7  Lautstärkeregler austauschen: Schritt 34, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 34, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 34, Bild 3 von 3
    • Fädle die Antennenkabel vorsichtig mit einer Pinzette aus dem Metallhalter auf dem Logic Board.

  33. iPhone 7  Lautstärkeregler austauschen: Schritt 35, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 35, Bild 2 von 2
    • Löse den unteren Kabelverbinder mit der Spudgerspitze.

    Wat voor kabel is dit? Deze is beschadigd bij mijn IPhone 8 Plus

    Maarten - Antwort

    • Entferne folgende Schrauben:

    • Eine 1,4 mm Kreuzschlitzschraube

    • Drei 2,2 mm Abstandsschrauben

    • Abstandsschrauben lassen sich am besten mit einem Schraubendreher für Abstandsschrauben herausdrehen.

    • Zur Not geht es auch mit einem kleinen Flachschraubendreher, du musst dabei aber aufpassen, dass du nicht abrutschst und umliegende Bauteile beschädigst.

    Link may be missing or broken!

    Standoff screws are best removed using an [linked product missing or disabled: IF145-343-1] and driver handle.

    Phrase Neither - Antwort

  34. iPhone 7  Lautstärkeregler austauschen: Schritt 37, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 37, Bild 2 von 2
    • Schiebe den Kolben des SIM Kartenauswerfers mit der Spudgerspitze aus dem Weg des Logic Boards.

  35. iPhone 7  Lautstärkeregler austauschen: Schritt 38, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 38, Bild 2 von 2
    • Hebe vorsichtig das Ende des Logic Boards mit dem Akkuanschluss hoch. Benutze dazu das flache Ende des Spudgers.

    • Achte darauf, dass du an keinen Kabeln ziehst. Falls du Widerstands spürst, prüfe nochmals, ob alle Kabel, Bauteile und Verbinder frei sind.

  36. iPhone 7  Lautstärkeregler austauschen: Schritt 39, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 39, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 39, Bild 3 von 3
    • Hebe das Logic Board am Ende mit dem Akkuanschluss hoch und ziehe es aus dem Rückgehäuse.

    • Achte darauf, dass sich das Logic Board nicht an irgendwelchen Kabeln verhakt.

  37. iPhone 7  Lautstärkeregler austauschen, Akku im hinteren Gehäuse: Schritt 40, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen, Akku im hinteren Gehäuse: Schritt 40, Bild 2 von 2
    • Ziehe mit einer stumpfen Pinzette einen der Klebestreifen an der unteren Kante des Akkus zurück.

  38. iPhone 7  Lautstärkeregler austauschen: Schritt 41, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 41, Bild 2 von 2
    • Ziehe mit einer stumpfen Pinzette den anderen der Klebestreifen an der unteren Kante des Akkus zurück.

  39. iPhone 7  Lautstärkeregler austauschen: Schritt 42, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 42, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 42, Bild 3 von 3
    • Versuche die Streifen während dieses Vorgangs glatt und knitterfrei zu halten. Verknitterte Streifen kleben zusammen und reißen anstatt sauber heraus zu kommen.

    • Ziehe langsam eine der Zuglaschen mit dem Klebestreifen weg vom Akku nach unten.

    • Ziehe gleichmäßig und halte die Spannung konstant, bis der Streifen zwischen Akku und Gehäuse ganz herausrutscht. Am Besten ziehst du etwa in einem Winkel von 60 Grad oder weniger.

    • Der Streifen verlängert sich dabei um ein Vielfaches. Fahre fort zu ziehen und fasse unter Umständen in der Nähe des Akkus nach.

  40. iPhone 7  Lautstärkeregler austauschen: Schritt 43, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 43, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 43, Bild 3 von 3
    • Wiederhole den vorherigen Schritt für den zweiten Streifen.

    • Halte den Akku fest während du den zweite Streifen entfernst, denn er könnte den Akku herausschleudern, wenn er sich vom Gehäuse löst.

    • Wenn du beide Klebestreifen erfolgreich entfernt hast, kannst du den nächsten Schritt überspringen.

    • Anderenfalls, wenn einer der beiden Streifen nicht ganz entfernt werden konnten fahre mit dem nächsten Schritt fort.

  41. iPhone 7  Lautstärkeregler austauschen: Schritt 44, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 44, Bild 2 von 2
    • Wenn du beide Streifen erfolgreich entfernt hast, dann gehe weiter zum nächsten Schritt. Im anderen Fall musst du den Akku heraushebeln.

    • Erwärme einen iOpener und lege ihn auf die Rückseite des Gehäuses direkt über dem Akku. Du kannst auch einen Haartrockner oder eine Heißluftpistole benutzen.

    • Entferne nach etwa einer Minute den iOpener, drehe das iPhone um und löse mit einer Plastikkarte jegliche Klebeverbindung auf der Rückseite des Akkus.

    • Vermeide es den Akku zu verbiegen. Ein Schaden am Akku kann gefährliche Chemikalien freisetzen oder ihn in Brand setzen.

    • Vermeide es im oberen Drittel des Akkus zu hebeln, du könntest das Flachbandkabel des Lautstärkeregelers beschädigen.

  42. iPhone 7  Lautstärkeregler austauschen: Schritt 45, Bild 1 von 1
    • Entferne den Akku aus dem Gehäuse.

    • Beim Zusammenbau hilft dir diese Anleitung den Akku wieder einzukleben.

  43. iPhone 7  Lautstärkeregler austauschen, Power- und Lautstärkereglerkabel: Schritt 46, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen, Power- und Lautstärkereglerkabel: Schritt 46, Bild 2 von 2
    • Entferne folgende Kreuzschlitzschrauben:

    • Zwei 1,9 mm Schrauben, die den An-/Ausschalter befestigen.

    • Drei 2,3 mm Schrauben, die die Lautstärketasten befestigen.

    You need to remove the battery first.

    Jasper Shemilt - Antwort

  44. iPhone 7  Lautstärkeregler austauschen: Schritt 47, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 47, Bild 2 von 2
    • Entferne folgende 1,3 mm Kreuzschlitzschrauben:

    • Eine neben der Rückkamera

    • Eine am Gehäuserückteil

  45. iPhone 7  Lautstärkeregler austauschen: Schritt 48, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 48, Bild 2 von 2
    • Drücke von außen mit der Spudgerspitze die Hold-Taste in das Gehäuse.

    • Dadurch lösen sich die Hold-Taste und die Dichtung vom Gehäuse.

  46. iPhone 7  Lautstärkeregler austauschen: Schritt 49, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 49, Bild 2 von 2
    • Entferne die Rückkamera mit einer Pinzette.

  47. iPhone 7  Lautstärkeregler austauschen: Schritt 50, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 50, Bild 2 von 2
    • Setze ein Plektrum von der Seite mit dem Einschaltknopf ein und trenne den Kleber, der das Flexkabel der Antenne am Gehäuse befestigt.

  48. iPhone 7  Lautstärkeregler austauschen: Schritt 51, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 51, Bild 2 von 2
    • Schiebe die Spitze des Plektrums unter das Antennenflexkabel in Richtung Oberkante des iPhones und trenne so noch bestehende Klebeverbindungen.

  49. iPhone 7  Lautstärkeregler austauschen: Schritt 52, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 52, Bild 2 von 2
    • Ziehe das Antennenflexkabel mit einer Pinzette weg vom Rand des iPhones und befreie so die geschraubte Klammer vom Gehäuse .

    • Entferne das Antennenflexkabel.

    • Entferne die 2,3 mm Abstandsschraube, mit der die Blitzhalterung am hinteren Gehäuse befestigt ist.

    • Am besten drehst du sie mit einem speziellen iPhone Abstandsschraubendreherbit und einem Bithalter heraus.

    • Zur Not geht es auch mit einem kleinen Schlitzschraubendreher, du musst aber aufpassen, dass er nicht verrutscht und die umliegenden Komponenten beschädigt.

  50. iPhone 7  Lautstärkeregler austauschen: Schritt 54, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 54, Bild 2 von 2
    • Entferne die Halteklammer des Blitzes.

  51. iPhone 7  Lautstärkeregler austauschen: Schritt 55, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 55, Bild 2 von 2
    • Löse vorsichtig die Blitzmodul mit der Spudgerspitze aus seinem Sitz.

  52. iPhone 7  Lautstärkeregler austauschen: Schritt 56, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 56, Bild 2 von 2
    • Ein "Halberd Spudger" hat eine Klinge in Hellenbardenform. Trenne damit den Kleber, der das Mikrofon am Gehäuse festhält.

  53. iPhone 7  Lautstärkeregler austauschen: Schritt 57, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 57, Bild 2 von 2
    • Falte vorsichtig das ganze Einschaltmodul vom Rand des Gehäuses weg.

  54. iPhone 7  Lautstärkeregler austauschen: Schritt 58, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 58, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 58, Bild 3 von 3
    • Schiebe die Klinge eines Hellebardenspudgers unter das Ende des Kabels mit dem An-/Ausschalter, um es vom Kleber auf dem rückwärtigen Gehäuse zu lösen.

    • Fahre mit Trennen fort und bewege die Klinge in Richtung des Oberteils des iPhones.

  55. iPhone 7  Lautstärkeregler austauschen: Schritt 59, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 59, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 59, Bild 3 von 3
    • Schiebe die Klinge des Hellebardenspudgers weiter unter dem Lautstärkekabel fort.

    • Bewege dabei die Klinge ganz langsam, um das Kabel nicht zu beschädigen.

  56. iPhone 7  Lautstärkeregler austauschen: Schritt 60, Bild 1 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 60, Bild 2 von 3 iPhone 7  Lautstärkeregler austauschen: Schritt 60, Bild 3 von 3
    • Schiebe die Klinge des Hellebardenspudgers unter den Teil des Kabels mit der Lautstärkeregelung.

    • Schiebe sie vorsichtig unter dem Kabel in Richtung Unterteil des iPhones und löse so die restlichen Klebeverbindungen.

  57. iPhone 7  Lautstärkeregler austauschen: Schritt 61, Bild 1 von 1
    • Entferne das Strom- und Lautstärkeregler-Flachbandkabel.

    Thank you very much for this guide, I did the job perfectly, without this guide I would not have succeeded.

    Thanks thanks thanks :-)

    agibru - Antwort

  58. iPhone 7  Lautstärkeregler austauschen, Lautstärkeregler: Schritt 62, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen, Lautstärkeregler: Schritt 62, Bild 2 von 2
    • Ziehe die Klammer der Lautstärkereglertaste nach unten, um sie aus ihrer Halterung zu befreien.

    Use the small flat end of a screw driver to push up the rt hand side of the bracket once youve removed the wire clip and also use to push up and pre release the lefthand side of the bracket. easier than pliers as it needs a bit of force and its safer as you dont want to break the plastic pins!

    ANDREW - Antwort

  59. iPhone 7  Lautstärkeregler austauschen: Schritt 63, Bild 1 von 2 iPhone 7  Lautstärkeregler austauschen: Schritt 63, Bild 2 von 2
    • Ziehe die Klammer nach oben, um sie zu entfernen.