Einleitung

Use this guide to replace your display inverter.

  1. Lay the iMac display-side down on a flat surface.
    • Lay the iMac display-side down on a flat surface.

    • Loosen the three Phillips screws securing the rear panel to the iMac.

    • These screws are captive in the iMac. The center screw will stop turning after about 3.5 turns and the outer screws will stop turning after about 5.5 turns. Do not try to remove these screws from your iMac.

    Some models (with light sensor) have only the two outboard screws.

    Robert Huber - Antwort

  2. Lift the rear panel slightly near the bottom of the iMac.
    • Lift the rear panel slightly near the bottom of the iMac.

    • Pull the rear panel toward yourself and remove it from the iMac.

    Kommentar hinzufügen

    • Rotate each of the two RAM retaining arms away from the RAM chip.

    • Pull the RAM chip straight away from its socket.

    • Repeat this process for the other RAM chip.

    • Be sure the RAM arms are rotated fully outward before installing new RAM chips.

    Kommentar hinzufügen

    • Remove the following three screws securing the inverter to the chassis:

      • Two 7.9 mm Phillips.

      • One 26 mm Phillips.

    • When reinstalling the inverter, be careful to route the purple and black cables around the screw mount. It is very easy to pinch the cable and damage the insulation.

    Kommentar hinzufügen

    • Slide the inverter toward the edge of the mid-plane, then lift it out of the iMac.

    • Be careful to not pry up against the RAM brackets.

    • When reinstalling the inverter, press the blue and white cables down in the edge of the midplane before lowering the inverter down into the midplane. The black cable can be routed near the hard drive thermal sensor cable.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    • Disconnect the large inverter cable connector from the inverter by pulling straight away from its socket.

    Kommentar hinzufügen

    • Disconnect the small inverter cable connector by pulling it straight away from its socket.

    Kommentar hinzufügen

    • Disconnect the hard drive thermal sensor cable from the thermal sensor board on the hard drive bracket by pulling the cable away from the heat sink.

    Kommentar hinzufügen

    • Gently pull the black inverter cable to disconnect it from the logic board.

    • If you have trouble plugging this cable back in during reinstallation, remove the fan duct for more room to work.

    Kommentar hinzufügen

    • Flip up the inverter cable cover from its left edge and lift it out of the chassis.

    Kommentar hinzufügen

    • De-route the inverter cables from the inverter cable cover hook.

    Kommentar hinzufügen

    • Remove the inverter cables from the inverter cable cover, and disconnect both connectors.

    Kommentar hinzufügen

    • If you wish to replace just the inverter board, use a spudger to pry off its plastic cover.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

4 weitere Nutzer haben diese Anleitung absolviert.

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 13

Insgesamt: 8,555