Au lycée j’ai commencé à bricoler sur un modèle réduit de Modélisme automobile radiocommandé R/C, réparer la transmission d’un modèle réduit 1/10 de Buggy 4RWD électrique a constitué l’une de mes premières vraies expériences en réparation.
La réparation d’appareils est devenue pour moi un hobby très pratique, car j’ai eu l’occasion de constater qu’avoir des compétences en réparation peut s’avérer fort utile au quotidien et aussi en milieu professionnel.
Au fur et à mesure des réparations d’appareils que j’ai eu l’occasion d’effectuer, j’ai pu acquérir pas mal d’expérience me permettant ainsi de réparer les problèmes logiciels et matériels sur les ordinateurs (serveurs, fixes et portables), mais aussi sur les robots domestiques.
Bonjour, oui il peut aller jusqu'à 8Go maximum.
Bonjour, Il faut vérifier qu'il n'y a plus de vis qui maintient la pièce. Attention, sur certains modèles de PC portables il peut y avoir des vis sous le caoutchouc des pieds du pc.
Just try to unplug then plug the phone to the charger again :)
Quel dommage pour Fairphone d’avoir vendu un produit non réparable qui de plus est vendu sans pièce détachée… il fait tache une série d’appareils à la réparabilité quasi parfaite.
C’est d’autant plus dommage que les possibilités de rendre mieux réparables les écouteurs sans fils sont nombreuses, voici quelques propositions :
- La batterie des écouteurs peut être rendue réparable, Sony l’a démontré avec certains de ses écouteurs sans fils (voir les WF-1000XM3) depuis 2 séries maintenant (mais Sony ne vend pas de pièces détachées, c’est dommage…).
- Les écouteurs pourraient être achetés individuellement avec la possibilité de les appairer entre eux à nouveau afin de conserver le boitier d’origine.
- La batterie du boitier peut être rendue réparable très facilement par l’utilisation de pile bouton rechargeable au lithium de 500mAh qui pourrait être facilement remplaçable en ouvrant une sorte de tiroir sur le boitier.
- Le boitier peut être rendu facilement démontable en utilisant des vis à la place des clips.
Ce tutoriel est aussi valable pour les sockets Intel à “matrice de pastilles” (Land Grid Array) sauf que dans le cas d’un socket LGA les pins à relever seront sur le socket plutôt que sur le processeur, mais le principe est le même, j’ai pu sauver une carte mère avec un socket LGA 1155 comme ça.
Exemple de socket LGA ou les pins sont bien visibles : https://upload.wikimedia.org/wikipedia/c...
Les pins sur les sockets sont très petits, mais avec une pincette de précision (visible dans ce tutoriel) comme celle d’iFixit c’est faisable.
Petite précision :
Les broches sur lesquels il faut brancher les connecteurs des différents éléments du boitier sont indiquées dans la notice de la carte mère (button power, LEDs, etc.). L’emplacement et l’ordre de branchement des différents éléments du boitier est susceptible de varier selon le modèle de la carte mère.
Cela concerne aussi le buzzer si vous en avez un.
This is really hard to find, I was not able to find spare part for the laptop models number you specified. I only could find a battery approaching the one shown in the pictures on this iFixit tutorial with the same manufacturer, voltage, capacity and battery model number : YUKU 2771141 3.7v and 3500 mAh but I cannot grant it will work, as the circuitry on the battery can be different / incompatible as this same exact battery manufacturer and battery model number have been used by another laptop manufacturer for other laptop models.
If your batteries are the same as the one shown in the picture above, you can try to find YUKU 2771141 on Google as this exact manufacturer / battery model can be found as spare part for laptops with manufacturer “Casper” and model number “N240” or “N220”.
But I cannot grant compatibility, especificaly concerning the protection circuitry (BMS) or connector. You may need to keep the old battery connector in order to soldering instead of of the new battery connector.
It also might not work at all.
Please ensure the fan metal case is not bent and ensure the fan is properly mounted. If this doesn’t solve your problem, your new fan is defective.
Principle of thermal paste is to fill the imperfections between the PS3 CPU and the surface of the heat sink.
Dry thermal paste can be okay if your PS3 is not overheating as long as you don’t remove the PS3 CPU cooler.
Sometime, with age, the thermal paste dry and does not make contact enough between the PS3 CPU and the surface of the heat sink. At this moment, the heat is not conduct well, the fan must spin faster to cool down the CPU and this is when you need to replace the thermal paste.
Overheat can also be just caused by a dirty or clogged fan.
When PS3 overheats, it can also shutdown suddenly and need to cool down before to be powered on again.
If you never did this before, you should consider replacing the thermal paste if your PS3 has one of these issues or if you want to improve the thermal conductivity as some thermal paste are more efficient than the one factory installed on the CPU.
Changing the thermal paste is an opportunity to clean the fan.
Low and stable operation temperature help to prevent the YLOD.
Just open the fob, like in this tutorial. The key is just a piece of metal.
Then place the key in a new fob (or replace only the fob plastic case for a cheaper solution).
Seite 1 von 3
Weiter